欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68C912B32FU8
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 16-Bit Microcontroller
中文描述: 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 46/128頁
文件大?。?/td> 748K
代理商: MC68C912B32FU8
MOTOROLA
46
MC68HC912B32
MC68HC912B32TS/D
7.8 Program/Erase Protection Interlocks
The Flash EEPROM program and erase mechanisms provide maximum protection from accidental pro-
gramming or erasure.
The voltage required to program/erase the Flash EEPROM (V
FP
) is supplied via an external pin. If V
FP
is not present, no programming/erasing will occur. Furthermore, the program/erase voltage will not be
applied to the Flash EEPROM unless turned on by setting a control bit (ENPE). The ENPE bit may not
be set unless the programming address and data latches have been written previously with a valid ad-
dress. The latches may not be written unless enabled by setting a control bit (LAT). The LAT and ENPE
control bits must be written on separate writes to the control register (FEECTL) and must be separated
by a write to the programming latches. The ERAS and LAT bits are also protected when ENPE is set.
This prevents inadvertent switching between erase/program mode and also prevents the latched data
and address from being changed after a program cycle has been initiated.
7.9 Stop or Wait Mode
When stop or wait commands are executed, the MCU puts the Flash EEPROM in stop or wait mode. In
these modes the Flash module will cease erasure or programming immediately. It is advised not to enter
stop or wait modes when programming the Flash array.
CAUTION
The Flash EEPROM module is not able to recover from STOP without a 1 micro-
second delay. This cannot be controlled internal to the MCU. Therefore, do not at-
tempt to recover from STOP with an interrupt. Use RESET to recover from a STOP
mode executed from Flash EEPROM. Recovery from a STOP instruction executed
from EEPROM and RAM operate normally.
7.10 Test Mode
The Flash EEPROM has some special test functions which are only accessible when the device is in
test mode.
Test mode is indicated to the Flash EEPROM module when the SMOD line on the LIB is
asserted. When SMOD is asserted, the special test control bits may be accessed via the LIB to invoke
the special test functions in the Flash EEPROM module. When SMOD is not asserted, writes to the test
control bits have no effect and all bits in the test register FEETST will be cleared. This ensures that
Flash EEPROM test mode cannot be invoked inadvertently during normal operation.
Note that the Flash EEPROM module will operate normally, even if SMOD is asserted, until a special
test function is invoked. The test mode adds additional features over normal mode which allow the tests
to be performed even after the device is installed in the final product.
相關PDF資料
PDF描述
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
相關代理商/技術參數
參數描述
MC68CK16Z1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CK16Z1CAG16 功能描述:16位微控制器 - MCU 16BIT 1KRAM 32KHZ CRYSTAL RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68CK16Z1CAG16 制造商:Freescale Semiconductor 功能描述:Microcontroller
MC68CK16Z1CFC16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CK16Z1CPV16 功能描述:16位微控制器 - MCU 16 Bit 16MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
主站蜘蛛池模板: 福贡县| 内丘县| 台安县| 晴隆县| 周宁县| 旬阳县| 丰宁| 沛县| 基隆市| 平谷区| 安西县| 饶平县| 临桂县| 内黄县| 普陀区| 革吉县| 垫江县| 辽中县| 瑞丽市| 常山县| 高尔夫| 莒南县| 邮箱| 文安县| 明溪县| 壤塘县| 德惠市| 临颍县| 襄城县| 东宁县| 益阳市| 罗江县| 兴国县| 淮阳县| 盘锦市| 深水埗区| 达孜县| 蓬莱市| 武乡县| 黑水县| 开鲁县|