- 您現在的位置：買賣IC網 > PDF目錄371126 > MMSD701T1 (MOTOROLA INC) SOD-123 Schottky Barrier Diodes PDF資料下載
參數資料
| 型號： | MMSD701T1 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 參考電壓二極管 |
| 英文描述： | SOD-123 Schottky Barrier Diodes |
| 中文描述： | SILICON, VHF-UHF BAND, MIXER DIODE |
| 文件頁數： | 4/6頁 |
| 文件大小： | 94K |
| 代理商： | MMSD701T1 |
4
Motorola Small–Signal Transistors, FETs and Diodes Device Data
INFORMATION FOR USING THE SOD–123 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOD–123
éééé
éééé
éééé
éééé
éééé
éééé
éééé
éééé
mm
inches
0.91
0.036
1.22
0.048
2.36
0.093
4.19
0.165
SOD–123 POWER DISSIPATION
The power dissipation of the SOD–123 is a function of the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
by TJ(max), the maximum rated junction temperature of the
die, R
θ
JA, the thermal resistance from the device junction to
ambient, and the operating temperature, TA. Using the
values provided on the data sheet for the SOD–123
package, PD can be calculated as follows:
TJ(max) – TA
R
θ
JA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25
°
C, one can
PD =
calculate the power dissipation of the device which in this
case is 225 milliwatts.
PD =
125
°
C – 25
°
C
444
°
C/W
= 225 milliwatts
The 444
°
C/W for the SOD–123 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOD–123 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad
. Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相關PDF資料 |
PDF描述 |
|---|---|
| MMSF10N02Z | Hook-Up Wire; Conductor Size AWG:24; No. Strands x Strand Size:19 x 36; Jacket Color:Black; Approval Bodies:UL; Approval Categories:UL AWM Style 1213; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/4 Type E RoHS Compliant: Yes |
| MMSF10N03Z | SINGLE TMOS POWER MOSFET 10 AMPERES 30 VOLTS |
| MMSF2P02E | SINGLE TMOS POWER MOSFET 2.5 AMPERES 20 VOLTS |
| MMSF3205 | SINGLE TMOS POWER MOSFET 11 AMPERES 20 VOLTS |
| MMSF3300 | SINGLE TMOS POWER MOSFET 30 VOLTS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MMSD701T1G | 功能描述:肖特基二極管與整流器 70V 225mW Single RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| MMSD71RKT1 | 功能描述:二極管 - 通用，功率，開關 80V 200mA RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| MMSD71RKT1G | 功能描述:二極管 - 通用，功率，開關 80V 200mA RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| MMSD914 | 功能描述:整流器 Hi Conductance Fast RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| MMSD914_05 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Small Signal Diode |
發布緊急采購，3分鐘左右您將得到回復。