- 您現在的位置：買賣IC網 > PDF目錄361089 > NCN6004AFTBR2 (ON SEMICONDUCTOR) Dual SAM/SIM Interface Integrated Circuit PDF資料下載
參數資料
| 型號： | NCN6004AFTBR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 其它接口 |
| 英文描述： | Dual SAM/SIM Interface Integrated Circuit |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PQFP48 |
| 封裝： | PLASTIC, TQFP-48 |
| 文件頁數： | 16/40頁 |
| 文件大小： | 329K |
| 代理商： | NCN6004AFTBR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
NCN6004A
http://onsemi.com
16
Table 3. Status Pins Data
STATE
(HEX)
PGM
A3
A2
A1
A0
CARD_SEL
STATUS #A
STATUS #B
00
1
X
X
0
0
X
Vcc_V
_OK Pass = Low
VCC_OK Fail = High
01
1
X
X
0
1
1
CRD_VCC_A In Range
Pass = High Fail =Low
02
1
X
X
1
0
1
CRD_VCCA Overloaded
Pass = High Fail = Low
03
1
X
X
1
1
1
CRD_DET_A
Card Present = High
00
1
X
X
0
0
X
VCC_OK Pass = Low
VCC_OK Fail = High
01
1
X
X
0
1
0
CRD_VCC_B In Range
Pass = High Fail =Low
02
1
X
X
1
0
0
CRD_VCC_B Overloaded
Pass = High Fail = Low
03
1
X
X
1
1
0
CRD_DET_A
Card Present = High
*The STATUS register is not affected when the NCN6004A operates in any of the programming mode.
Initialized conditions upon start-up are depicted by bold characters in Table 2 and Table 4.
Vbat
2.10 V
2.00 V
2.70 V
3.30 V
Vbat_OK
Vbat STATUS
Max. ANLG_VCC Under Voltage
Min. ANLG_VCC Under Voltage
Typical ANLG_VCC Operating Voltage
The input power supply voltage monitoring applies to the card selected.
Figure 5. Reading ANLG_VCC Status (monitoring ANLG_VCC input voltage)
SYSTEM STATES UPON UPON START-UP
Table 4. Operating Conditions Upon Start-up
CRD_VCC_A
3.0 V
CRD_VCC_B
3.0 V
CRD_CLK_A
1/1 Ratio
CRD_CLK_B
1/1 Ratio
CRD_CLK_A
START (clock is valid)
CRD_CLK_B
START (clock is valid)
CRD_CLK_A
Low Speed Slope
CRD_CLK_B
Low Speed Slope
CLOCK Route
Direct (CLK_A
→
A, CLK_B
→
B)
Depending upon the logic state at turn on present on
pin 44, the system will run into a parallel mode
(MUX_MODE = L)
or
(MUX_MODE = H). It is not possible to change the logic
state once the system is running.
Similarly, depending upon the logic state present pin 45,
the internal pull up resistors (I/O_A and I/O_B line) will be
either connected to ANLG_VCC voltage (EN_RPU = H) or
disconnected (EN_RPU = L). It is not possible to change this
operating condition once the system is running.
a
multiplexed
mode
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6004A | Dual SAM/SIM Interface Integrated Circuit |
| NCN6010DTBR2 | SIM Card Supply and Level Shifter |
| NCN6010 | SIM Card Supply and Level Shifter |
| NCN6010D | SIM Card Supply and Level Shifter |
| NCN6010DTB | SIM Card Supply and Level Shifter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6004AFTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6010 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
發布緊急采購，3分鐘左右您將得到回復。