- 您現在的位置：買賣IC網 > PDF目錄361091 > NCP1406SNT1 (ON SEMICONDUCTOR) 25 V/25 mA PFM Step−Up DC−DC Converter PDF資料下載
參數資料
| 型號： | NCP1406SNT1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | 25 V/25 mA PFM Step−Up DC−DC Converter |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封裝： | SC-59, SOT-23, TSOP-5 |
| 文件頁數： | 14/23頁 |
| 文件大小： | 224K |
| 代理商： | NCP1406SNT1 |
NCP1406
http://onsemi.com
14
Input Capacitor
The input capacitor stabilizes the input voltage and
minimizes peak current ripple from the power source. The
capacitor should be connected directly to the inductor pin
where the input voltage is applied in order to effectively
smooth the input current ripple and voltage due to the
inductor current ripple. The input capacitor is also used to
decouple the high frequency noise from the VDD supply to
the internal control circuit; therefore, the capacitor should
be placed close to the VDD pin. For some particular
applications, separate decoupling capacitors should be
provided and connected directly to the VDD pin for better
decoupling effect. A larger input capacitor can better
reduce ripple current at the input. By reducing the ripple
current at the input, the converter efficiency can be
improved. In general, a 4.7 F to 22 F ceramic input
capacitor is sufficient for most applications. X5R and X7R
type ceramic capacitors are recommended due to their
good capacitance tolerance and stable temperature
behavior.
Output Capacitor
The output capacitor is used for sustaining the output
voltage when no current is delivering from the input, and
smoothing the ripple voltage. Ceramic capacitors should
be used for the output capacitor due to their low ESR at high
switching frequency and low profile in physical size. In
general, a 3.3 F to 22 F ceramic capacitor should be
appropriate for most applications. X5R and X7R type
ceramic capacitors are recommended due to their good
capacitance tolerance and temperature coefficient, while
Y5V type ceramic capacitors are not recommended since
both their capacitance tolerance and temperature
coefficient are too large. The output voltage ripple and
switching frequency at nominal load current can be
calculated by the following equations:
Vripple
IOUT
COUT
(IPKIOUT)
1
fSW(Load)
IPK
L
VOUT
VDVIN
ESR
fSW(Load)
2IOUT(VOUT
VDVIN)
I2
PK
L
Where I
OUT
is the nominal load current, C
OUT
is the
selected output capacitance, I
PK
is the peak inductor
current, L is the selected inductance, V
OUT
is the output
voltage, V
D
is the Schottky diode forward voltage, V
IN
is
the input voltage, ESR is the ESR of the output capacitor.
Feedback Resistors
To achieve better efficiency at light load, a high
impedance feedback resistor divider should be used.
Choose the lower resistor R2 value from the range of 10 k
to 200 k . The value of the upper resistor R1 can then be
calculated from the equation below:
VOUT
R1
R2
1.19
1
1% tolerance resistors should be used for both R
1
and R
2
for better V
OUT
accuracy.
Feedforward Capacitor
A feedforward capacitor is required to add across the
upper feedback resistor to avoid double pulsing or group
pulsing at the switching node which will cause larger
inductor ripple current and higher output voltage ripple.
With adequate feedforward capacitance, evenly distributed
single pulses at the switching node can be achieved. The
range of the capacitor value is from 5.0 pF to 200 pF for
most applications. For NCP1406, the lower the switching
frequency, the larger the feedforward capacitance is
needed; besides, the higher the output voltage, the larger
the feedforward capacitance is required. For the initial trial
value of the feedforward capacitor, the following equation
can be used; however, the actual value needs fine tuning:
CFF
1
2
fSW(Load)
20
R1
Output Voltage Higher than 25 V
The NCP1406 can be used to generate output voltage
higher than 25 V by adding an external high voltage NCh
MOSFET in series with the internal MOSFET switch as
shown in Figure 51. The draintosource breakdown
voltage of the external MOSFET must be at least 1.0 V
higher than the output voltage. The diode D2 connected
across the gate and the source of the external MOSFET
helps the external MOSFET to turn off and ensures that
most of the voltage drops across the external MOSFET
during the switchoff period. Since the high voltage
external MOSFET is in series with the internal MOSFET,
higher break down voltage is achieved but the current
capability is not increased.
There is an alternative application circuit shown in
Figure 53 which can output voltage up to 30 V. For this
circuit, a diodecapacitor chargepump voltage doubler
constructed by D2, D3 and C1 is added. During the internal
MOSFET switchon time, the LX pin is shorted to ground
and D2 will charge up C1 to the stepped up voltage at the
cathode of D1. During the MOSFET switchoff time, the
voltage at V
OUT
will be almost equal to the double of the
voltage at the cathode of D1. The V
OUT
is monitored by the
FB pin via the resistor divider and can be set by the resistor
values. Since the maximum voltage at the cathode of D1 is
15 V, the maximum V
OUT
is 30 V. The value of C1 can be in
the range of 0.47 F to 2.2 F.
Negative Voltage Generation
The NCP1406 can be used to produce a negative voltage
output by adding a diodecapacitor chargepump circuit
(D2, D3, and C1) to the LX pin as shown in Figure 50. The
feedback voltage resistor divider is still connected to the
positive output to monitor the positive output voltage and
a small value capacitor is used at C2. When the internal
MOSFET switches off, the voltage at the LX pin charges
up the capacitor through diode D2. When the MOSFET
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1406SNT1G | 25 V/25 mA PFM Step−Up DC−DC Converter |
| NCP1410DMR2 | 250 mA Sync-Rect PFM Step-Up DC-DC Converter with Low-Battery Detector |
| NCP1410 | 250 mA Sync-Rect PFM Step-Up DC-DC Converter with Low-Battery Detector |
| NCP1411DMR2 | Sync-Rect PFM Step-Up DC-DC Converter with Low-Battery Detector and Ring-Killer |
| NCP1411D | Sync-Rect PFM Step-Up DC-DC Converter with Low-Battery Detector and Ring-Killer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1406SNT1G | 功能描述:直流/直流開關轉換器 25V 25mA Boost PFM RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1406V15GEVB | 功能描述:電源管理IC開發工具 NCP1406 EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1406V25GEVB | 功能描述:電源管理IC開發工具 NCP1406 EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1410DMR2 | 功能描述:直流/直流開關轉換器 ANA DC-DC CONVERTER RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1410DMR2G | 功能描述:直流/直流開關轉換器 ANA DC-DC CONVERTER RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。