- 您現在的位置：買賣IC網 > Datasheet目錄46 > SC427MLTRT (Semtech)IC REG DL BUCK/LINEAR 32MLPQ Datasheet資料下載
參數資料
| 型號： | SC427MLTRT |
| 廠商： | Semtech |
| 文件頁數： | 23/33頁 |
| 文件大?。?/td> | 894K |
| 描述： | IC REG DL BUCK/LINEAR 32MLPQ |
| 標準包裝： | 1 |
| 系列： | EcoSpeed®, SmartDrive™ |
| 拓撲： | 降壓（降壓）（1），線性（LDO）（1） |
| 功能： | 任何功能 |
| 輸出數： | 2 |
| 頻率 - 開關： | 1MHz |
| 電壓/電流 - 輸出 1： | 可調，10A |
| 電壓/電流 - 輸出 2： | 5V，200mA |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 3 V ~ 28 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-MLPQ（5x5） |
| 包裝： | 標準包裝 |
| 其它名稱： | SC427MLDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
SC417/SC427
23
Applications Information (continued)
grammed to 3.3V. After start-up, the device would connect
VOUT to VLDO and disable the LDO, since the two volt-
ages are within the ?00mV switch-over window. To avoid
unwanted switch-over, the minimum difference between
the voltages for V
OUT
and V
LDO
should be ?00mV.
It is not recommended to use the switch-over feature for
an output voltage less than 3V since this does not provide
sufficient voltage for the gate-source drive to the internal
p-channel switch-over MOSFET.
Switch-over MOSFET Parasitic Diodes
The switch-over MOSFET contains parasitic diodes that
are inherent to its construction, as shown in Figure 11.
Switchover
MOSFET
Parasitic diode
Parasitic diode
V5V
V
LDO
V
OUT
Switchover
control
Figure 11 Switch-over MOSFET Parasitic Diodes
There are some important design rules that must be fol-
lowed to prevent forward bias of these diodes. The fol-
lowing two conditions need to be satisfied in order for the
parasitic diodes to stay off.
V5V e V
LDO
V5V e V
OUT
If either V
LDO
or V
OUT
is higher than V5V, then the respective
diode will turn on and the SC417/SC427 operating current
will flow through this diode. This has the potential of
damaging the device.
Using the On-chip LDO to Bias the SC417/SC427
The following steps must be followed when using the on-
chip LDO to bias the device.
Connect V5V to VLDO before enabling the LDO.
The LDO has an initial current limit of 85mA at
start-up, therefore, do not connect any external
load to VLDO during start-up.
"
"
"
"
When VLDO reaches 90% of its final value, the
LDO current limit increases to 200mA. At this
time the LDO may be used to supply the required
bias current to the device.
Attempting to operate in self-powered mode in any other
configuration can cause unpredictable results and may
damage the device.
Design Procedure
When designing a switch mode supply the input voltage
range, load current, switching frequency, and inductor
ripple current must be specified.
The maximum input voltage (V
INMAX
) is the highest speci-
fed input voltage. The minimum input voltage ( V
INMIN
) is
determined by the lowest input voltage after evaluating
the voltage drops due to connectors, fuses, switches, and
PCB traces.
The following parameters define the design.
Nominal output voltage (V
OUT
)
Static or DC output tolerance
Transient response
Maximum load current (I
OUT
)
There are two values of load current to evaluate con-
tinuous load current and peak load current. Continuous
load current relates to thermal stresses which drive the
selection of the inductor and input capacitors. Peak load
current determines instantaneous component stresses and
fltering requirements such as inductor saturation, output
capacitors, and design of the current limit circuit.
The following values are used in this design.
V
IN
= 12V + 10%
V
OUT
= 1.05V + 4%
f
SW
= 250kHz
Load = 10A maximum
Frequency Selection
Selection of the switching frequency requires making a
trade-off between the size and cost of the external filter
components (inductor and output capacitor) and the
power conversion efficiency.
"
"
"
"
"
"
"
"
"
相關PDF資料 |
PDF描述 |
|---|---|
| SE95D,112 | IC SENSOR TEMP 2.8-5.5V SOT96-1 |
| SE97BTP,547 | IC TEMP SENSOR DIMM 8HWSON |
| SE98ATP,547 | IC TEMP SENSOR DDR 8-HWSON |
| SG6901ASZ | IC PFC CTLR AVERAGE CURR 20SOIC |
| SG6932SZ | IC PFC CONTROLLER CCM 16SOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC428 | 制造商:Mallory 功能描述:Sonalert |
| SC4-28 | 功能描述:SCREW 4-40 HEX .5"L FOR CONN MNT RoHS:是 類別:盒，外殼，支架 >> 卡架 - 配件 系列:VectorPak™ 標準包裝:1 系列:VectorPak™ 附件類型:EFP 模塊 適用于相關產品:PCB |
| SC428312CFGE | 制造商:Freescale Semiconductor 功能描述: |
| SC42920FNR2 | 制造商:Motorola Inc 功能描述: |
| SC430769CFNER | 制造商:Freescale Semiconductor 功能描述:SMOKE DETECTOR |
發布緊急采購，3分鐘左右您將得到回復。