- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-LI STEPPER MOTOR CONTROLLER, QCC32 PDF資料下載
參數資料
| 型號： | TMC222-LI |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, QCC32 |
| 封裝： | QFN-32 |
| 文件頁數： | 32/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-LI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
38
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
7
Frequently Asked Questions
7.1
Using the bus interface
Q: How many devices can be operated on the same bus?
A: 32 devices can be discriminated by means of the physical address. However, it depends on some
factors if this high number really makes sense. First of all it has to be checked if each device can be
serviced under any circumstances in the maximum allowed time taking the bus speed and the
individual real-time requirements of each device into account. Second, the idea of reserving address 0
for OTP physical address programming during system installation and defective parts replacement
reduces the number to 30.
Q: How to program the OTP physical address bits of a device if there are more devices
connected to the same bus?
A: The problem here is that all new devices are shipped with the OTP physical address bits set to zero
making it difficult to address just one device with the SetOTPParam command. Use HW input as chip
select line to address just one device by SetOTPParam. If this is impractible since the HW input is
hardwired or not controllable for any other reason the only alternative is to assemble and program one
device after the other. I.e., assemble only first device and program the desired non-zero address, then
assemble the second device and program the desired non-zero address, and so on until all devices are
assembled and programmed. This is also a good service concept when replacing defective devices in
the field: The idea is that all devices are programmed to different non-zero physical addresses at
production/installation time. Once a defective device is being replaced the replacement part can easily
be addressed by SetOTPParam since it is the only part with physical address zero.
7.2
General problems when getting started
Q: What is the meaning of ElDef?
A: The ElDef flag (‘Electrical Defect’) is the logical ORing of the OVC1 and OVC2 flags. OVC1 is set to
one in case of an overcurrent (coil short) or open load condition (selected coil current is not reached)
for coil A. OVC2 is the equivalent for coil B.
Q: What could be the reason for ElDef / OVC1 / OVC2 being set to one?
A: There are a number of possible causes:
Motor not connected (
open load)
Connected motor has shorted coils (
overcurrent) or broken coils (
open load)
Motor coils connected to the wrong device pins
Selected coil current can not be reached (
open load) due to high coil impedance or low
supply voltage. Solution: Select a lower coil run/hold current or rise the supply voltage.
Generally: the calculated voltage required to reach a desired coil current at a given coil
resistance (V = I R) must be significantly lower than actual supply voltage due to the coil
inductivity.
Q: Should the external switch be normally closed or open when the reference position is hit?
A: The SWI input resp. the ESW flag have neither effect on any internal state machine nor on
command processing, even not on the RunInit command. ESW must be polled by software using
GetFullStatus1 command. The software can simply be adapted to whatever state the switch is in when
the reference position is hit, i.e. closed or open.
相關PDF資料 |
PDF描述 |
|---|---|
| TMC222-PI20 | STEPPER MOTOR CONTROLLER, PDSO20 |
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。