- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-LI STEPPER MOTOR CONTROLLER, QCC32 PDF資料下載
參數資料
| 型號： | TMC222-LI |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, QCC32 |
| 封裝： | QFN-32 |
| 文件頁數： | 9/48頁 |
| 文件大小： | 457K |
| 代理商： | TMC222-LI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
17
Copyright 2004-2009 TRINAMIC Motion Control GmbH & Co. KG
5.1.14 Internal handling of commands and flags
The internal handling of commands and flags differs. Commands are handled with different priorities
depending on the current state and the current status of internal flags, see figure below. SetPosition or
GotoSecurePosition commands are ignored as long as the <StepLoss> flag is set. Details can be
found in Table 8: Priority Encoder.
Note: A HardStop command is sent by the master or triggered internally in case of an electrical defect
or over temperature.
A description of the available commands can be found in 6.8 Command Description. A list of the
internal flags can be found in 5.2.2 Status Flags.
As an example: When the circuit drives the motor to its programmed target position, state “GotoPos” is
entered. There are three events which can cause to leave this state: HardStop command received,
SoftStop command received or target position reached. If all three events occur at the same time the
HardStop command is executed since it has the highest priority. The Motion finished event (target
position reached) has the lowest priority and thus will only cause transition to “Stopped” state when
both other events do not occur.
RunInit
SoftStop
Stopped
ShutDown
HardStop
GotoPos
Priorities
High
Low
Thermal Shutdown
GotoSecurePosition
SetPosition
Motion finished
HardStop
Thermal Shutdown
Power On
Reset
GetFullStatus1
AND <TSD> + <HS> = 0
HardStop
Thermal Shutdown
SoftStop
RunInit
Motion finished
Figure 7: Internal handling of commands and flags
相關PDF資料 |
PDF描述 |
|---|---|
| TMC222-PI20 | STEPPER MOTOR CONTROLLER, PDSO20 |
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。