- 您現在的位置：買賣IC網 > PDF目錄98285 > TPS65167RHAT (TEXAS INSTRUMENTS INC) 4.9 A SWITCHING REGULATOR, 900 kHz SWITCHING FREQ-MAX, PQCC40 PDF資料下載
參數資料
| 型號： | TPS65167RHAT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 4.9 A SWITCHING REGULATOR, 900 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, GREEN, PLASTIC, MO-220VJJD-2, QFN-40 |
| 文件頁數： | 11/41頁 |
| 文件大小： | 1270K |
| 代理商： | TPS65167RHAT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
www.ti.com
Overvoltage Protection
Input Capacitor Selection VINB, SUP, SUPN, AVIN, Inductor Input Terminal
Boost Converter Design Procedure
1. Converter Duty Cycle:
D + 1 *
Vin
h
Vout
2. Maximum output current:
Iout + Isw *
Vin
D
2
s
L
(1 * D)
3. Peak switch current:
I
swpeak +
Vin
D
2
s
L
)
Iout
1 * D
SLVS760C – APRIL 2007 – REVISED MARCH 2008
With:
VsHVS = Boost converter output voltage with HVS = high
VFB = 1.146 V
The main boost converter has an overvoltage protection of the main switch M1 if the feedback pin (FB) is floating
or shorted to GND causing the output voltage to rise. In such an event, the output voltage is monitored with the
overvoltage protection comparator on the SUP pin. As soon as the comparator trips at typically at 20 V then the
boost converter stops switching. The output voltage will fall below the overvoltage threshold and the converter
continues to operate. See Figure 4.
Note: During high voltage stress test the overvoltage protection is disabled.
For good input voltage filtering, low ESR ceramic capacitors are recommended. The TPS65167 has an analog
input AVIN as well as a power supply input SUP powering all the internal rails. A 1-
F bypass capacitor is
required as close as possible from AVIN to GND as well as from SUP to GND. The SUPN pin needs to be
bypassed with a 470-nF capacitor. Depending on the overall load current two or three 22-
F input capacitors are
required. For better input voltage filtering, the input capacitor values can be increased. To reduce the power
losses across the external isolation switch a filter capacitance at the input terminal of the inductor is required. To
minimize possible audible noise problems, two 10-
F capacitors in parallel are recommended. More capacitance
will further reduce the ripple current across the isolation switch. See Table 3 and the typical applications for input
capacitor recommendations.
Table 3. Input Capacitor Selection
CAPACITOR
COMPONENT SUPPLIER
COMMENTS
22
F/16 V
Taiyo Yuden EMK316BJ226ML
Pin VINB
2
×10 F/25 V
Taiyo Yuden TMK316BJ106KL
Pin VINB (alternative)
2
×10 F/25 V
Taiyo Yuden TMK316BJ106KL
Inductor input terminal
1
F/35 V
Taiyo Yuden GMK107BJ105KA
Pin SUP
1
F/25 V
Taiyo Yuden TMK107BJ105KA
Pin AVIN
470 nF/25 V
Taiyo Yuden TMK107BJ474MA
Pin SUPN
x
The first step in the design procedure is to verify whether the maximum possible output current of the boost
converter supports the specific application requirements. To simplify the calculation, the fastest approach is to
estimate the converter efficiency by taking the efficiency numbers from the provided efficiency curves or to use a
worst case assumption for the expected efficiency, e.g., 80%. With the efficiency number it is possible to
calculate the steady state values of the application.
With Isw = converter switch current (minimum switch current limit = 3.5 A)
fs = converter switching frequency (typical 750 kHz)
L = Selected inductor value
η = Estimated converter efficiency (use the number from the efficiency curves or 0.8 as an estimation)
Copyright 2007–2008, Texas Instruments Incorporated
19
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65170RHDT | 4.2 A SWITCHING REGULATOR, 900 kHz SWITCHING FREQ-MAX, PQCC28 |
| TPS65171RHAR | 4 A SWITCHED CAPACITOR REGULATOR, 900 kHz SWITCHING FREQ-MAX, PQCC40 |
| TPS65182BRGZT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65182RGZT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65182RGZR | POWER SUPPLY SUPPORT CKT, PQCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65167RHATG4 | 功能描述:LCD 驅動器 12V/3.5A(I/O) 4-CH Multi-Converter RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TPS65168RSBR | 功能描述:LCD 驅動器 Hi ResFully Prgrm LCD Bias IC RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TPS65170EVM-559 | 功能描述:電源管理IC開發工具 TPS65170 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS65170RHDR | 功能描述:其他電源管理 LCD Bias Supply RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel |
| TPS65170RHDT | 功能描述:其他電源管理 LCD Bias Supply RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。