- 您現在的位置：買賣IC網 > PDF目錄98286 > TRF7960RHBR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC32 PDF資料下載
參數資料
| 型號： | TRF7960RHBR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 封裝： | 5 X 5 MM, GREEN, PLASTIC, QFN-32 |
| 文件頁數： | 33/52頁 |
| 文件大小： | 1023K |
| 代理商： | TRF7960RHBR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Start
Condition
CLK
I/O_[7]
I/O_[6:0]
a0[6:0] d0[6:0]
xx
d1[6:0] d2[6:0]
dN[6:0]
d3[6:0]
xx
StopCont
ValidOuputData
a0[7]
d0[7]
d2[7]
dN[7]
d1[7]
d3[7]
InternalOE
OutputData
50ns
www.ti.com
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010
5.6.1
Receive
At the start of a receive operation (when SOF is successfully detected), B6 is set in the IRQ status
register. An interrupt request is sent to the MCU at the end of the receive operation if the receive data
string was shorter than or equal to 8 bytes. The MCU receives the interrupt request, then checks to
determine the reason for the interrupt by reading the IRQ status register (address 0Ch), after which the
MCU reads the data from the FIFO.
If the received packet is longer than 8 bytes, the interrupt is sent before the end of the receive operation
when the ninth byte is loaded into the FIFO (75% full). The MCU should again read the content of the IRQ
status register to determine the cause of the interrupt request. If the FIFO is 75% full (as marked with flag
B5 in IRQ status register and by reading the FIFO status register), the MCU should respond by reading
the data from FIFO to make room for new incoming receive data. When the receive operation is finished,
the interrupt is sent and the MCU must check how many words are still present in the FIFO before it
finishes reading.
If the reader detects a receive error, the corresponding error flag is set (framing error, CRC error) in the
IRQ status register, which indicates that the MCU reception was completed incorrectly.
5.6.2
Transmit
Before beginning data transmission, the FIFO should be cleared with a reset command (0F). Data
transmission is initiated with a selected command (described in the Direct Commands section,
Table 5-29). The MCU then commands the reader to do a continuous write command (3Dh, see
Table 5-31) starting from register 1Dh. Data written into register 1Dh is the TX length byte1 (upper and
middle nibbles), while the following byte in register 1Eh is the TX length byte 2 (lower nibble and broken
byte length). Note that the TX byte length determines when the reader sends the EOF byte. After the TX
length bytes are written, FIFO data is loaded in register 1Fh with byte storage locations 0 to 11. Data
transmission begins automatically after the first byte is written into the FIFO. The loading of TX length
bytes and the FIFO can be done with a continuous-write command, as the addresses are sequential.
At the start of transmission, the flag B7 (Irq_tx) is set in the IRQ status register. If the transmit data is
shorter than or equal to 4 bytes, the interrupt is sent only at the end of the transmit operation. If the
number of bytes to be transmitted is higher or equal to 5, then the interrupt is generated. This occurs also
when the number of bytes in the FIFO reaches 3. The MCU should check the IRQ status register and
FIFO status register and then load additional data to the FIFO, if needed. At the end of the transmit
operation, an interrupt is sent to inform the MCU that the task is complete.
Figure 5-7. Data Output Only When CLK Is High
Copyright 2006–2010, Texas Instruments Incorporated
System Description
39
相關PDF資料 |
PDF描述 |
|---|---|
| TRF7960RHBT | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TRF7961RHBR | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TRF7961RHBT | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TS(X)8387MFDSSC/SMD | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387MF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TRF7960RHBRG4 | 功能描述:RFID應答器 Multi-Std Fully Int 13.56MHz RFID AFE RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7960RHBT | 功能描述:RFID應答器 Mulit-Standard High Freq RFid Reader RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7960RHBT | 制造商:Texas Instruments 功能描述:RFID Reader IC 制造商:Texas Instruments 功能描述:IC, RFID READER, 13.56MHZ, QFN-32 |
| TRF7960RHBTG4 | 功能描述:RFID應答器 Mulit-Standard High Freq RFID Read/Writ RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TRF7960TB | 功能描述:射頻識別變換器工具 TRF7960 Target Board RoHS:否 制造商:Olimex Ltd. 產品:RFID Readers 用于:ISO15693 |
發布緊急采購，3分鐘左右您將得到回復。