- 您現在的位置：買賣IC網 > PDF目錄382687 > TSB41AB2I (Texas Instruments, Inc.) IEEE 1394a-2000 TWO-PORT CABLE TRANSCEVER/ARBITER PDF資料下載
參數資料
| 型號： | TSB41AB2I |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | IEEE 1394a-2000 TWO-PORT CABLE TRANSCEVER/ARBITER |
| 中文描述： | 個IEEE 1394a - 2000雙端口電纜TRANSCEVER /仲裁者 |
| 文件頁數： | 43/50頁 |
| 文件大?。?/td> | 662K |
| 代理商： | TSB41AB2I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
SLLS418G
–
JUNE 2000
–
REVISED JANUARY 2003
43
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
interface reset and disable (continued)
The sequence of events for resetting the PHY-LLC interface when it is in the differentiated mode of operation
(ISO terminal is low) is as follows:
1
a.
Normal operation. Interface is operating normally, with LPS active, SYSCLK active, status and packet
data reception and transmission via the CTL and D lines, and request activity via the LREQ line.
b.
LPS deasserted. The LLC deasserts the LPS signal and, within 1
μ
s, terminates any request or interface
bus activity, and places its LREQ, CTL, and D outputs into a high-impedance state (the LLC should
terminate any output signal activity such that signals end in a logic 0 state).
c.
Interface reset. After T
LPS_RESET
time, the PHY determines that LPS is inactive, terminates any
interface bus activity, and places its CTL and D outputs into a high-impedance state (the PHY
terminates any output signal activity such that signals end in a logic 0 state). The PHY-LLC interface
is now in the reset state.
d.
Interface restored. After the minimum T
RESTORE
time, the LLC may again assert LPS active. (The
minimum T
RESTORE
interval provides sufficient time for the biasing networks used in Annex J type
isolation barrier circuits to stabilize and reach a quiescent state if the isolation barrier has somehow
become unbalanced.) When LPS is asserted, the interface initializes as described below.
SYSCLK
ISO
(High)
(a)
(c)
(b)
CTL0, CTL1
D0
–
D7
LREQ
LPS
(d)
TLPS_RESET
TRESTORE
Figure 23. Interface Reset, ISO High
相關PDF資料 |
PDF描述 |
|---|---|
| TSB41LV03AI | IEEE 1394a THREE-PORT CABLE TRANSCEIVER/ARBITER |
| TSC692E | 672-pin FineLine BGA |
| TSC695F | IC,FPGA,57120-CELL,CMOS,BGA,1020PIN,PLASTIC |
| TSC695FL | IC,FPGA,79040-CELL,CMOS,BGA,1020PIN,PLASTIC |
| TSL1301 | 102 x 1 Linear Sensor Array with Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB41AB2IPAP | 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| TSB41AB2PAP | 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| TSB41AB2PAP(PBF) | 制造商:Texas Instruments 功能描述: |
| TSB41AB2PAPG4 | 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| TSB41AB2PAPR | 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。