- 您現在的位置：買賣IC網 > PDF目錄98303 > TSC2301IPAGRG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | TSC2301IPAGRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封裝： | GREEN, PLASTIC, TQFP-64 |
| 文件頁數： | 14/95頁 |
| 文件大小： | 1322K |
| 代理商： | TSC2301IPAGRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
www.ti.com
TSC2301
SLAS371D – SEPTEMBER 2002 – REVISED AUGUST 2004
Reference
The TSC2301 has an internal voltage reference that can be set to 1.2 V or 2.5 V, through the reference control
register. This reference can also be set to automatically power down between conversions to save power, or
remain on to reduce settling time.
The internal reference voltage is only used in the single-ended mode for battery monitoring, temperature
measurement, and for utilizing the auxiliary inputs. Optimal touch screen performance is achieved when using a
ratiometric conversion, thus all touch screen measurements are done automatically in the differential mode.
An external reference can also be applied to the VREFIN pin, and the internal reference can be turned off.
Variable Resolution
The TSC2301 provides three different resolutions for the ADC: 8, 10, or 12 bits. Lower resolutions are often
practical for measurements such as touch pressure. Performing the conversions at lower resolution reduces the
amount of time it takes for the ADC to complete its conversion process, which lowers power consumption.
Conversion Clock and Conversion Time
The TSC2301 contains an internal 8-MHz clock, which is used to drive the state machines inside the device that
perform the many functions of the part. This clock is divided down to generate the actual ADC conversion clock.
The division ratio for this clock is set in the ADC control register. The ability to change the conversion clock rate
allows the user to choose the optimal value for resolution, speed, and power. If the 8-MHz clock is used directly,
the ADC is limited to 8-bit resolution; using higher resolutions at this speed does not result in accurate
conversions. Using a 4-MHz conversion clock is suitable for 10-bit resolution; 12-bit resolution requires that the
conversion clock run at 1 or 2 MHz.
Regardless of the conversion clock speed, the internal clock runs nominally at 8 MHz. The conversion time of the
TSC2301 is dependent upon several functions. While the conversion clock speed plays an important role in the
time it takes for a conversion to complete, a certain number of internal clock cycles is needed for proper
sampling of the signal. Moreover, additional times, such as the panel voltage stabilization time, can add
significantly to the time it takes to perform a conversion. Conversion time can vary depending upon the mode in
which the TSC2301 is used. Throughout this data sheet, internal and conversion clock cycles are used to
describe the times that many functions take. In considering the total system design, these times must be taken
into account by the user.
Touch Detect
The pen interrupt (PENIRQ) output function is detailed in Figure 49. While in the touch screen monitoring mode,
the Y- driver is ON and connected to GND, the X+ input is connected through a pullup resistor to VDD, and the
PENIRQ output reflects the state of the X+ input. When the panel is touched, the X+ input is pulled to ground
through the touch screen and PENIRQ output goes LOW due to the current path through the panel to GND,
initiating an interrupt to the processor. During the measurement cycles for X- and Y-position, the X+ input is
disconnected from PENIRQ to eliminate any leakage current from the pullup resistor that might flow through the
touch screen, thus causing no errors.
21
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2302IRGZRG4 | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| TSDC4872IJT | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| TS4872IJT | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| TSH103ID | 3 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| TSH103IDT | 3 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC2301IZQZ | 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2301IZQZR | 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2301PAG | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2301PAGR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2302 | 制造商:BB 制造商全稱:BB 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
發布緊急采購，3分鐘左右您將得到回復。