欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TSC2301IPAGRG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝: GREEN, PLASTIC, TQFP-64
文件頁數: 31/95頁
文件大?。?/td> 1322K
代理商: TSC2301IPAGRG4
www.ti.com
Bit 13 — PLLO
TSC2301
SLAS371D – SEPTEMBER 2002 – REVISED AUGUST 2004
Bit 15 — SDAV (write only)
SPI Data Available. This read-only bit mirrors the function of the DAV pin. This bit is provided so that the host
processor can poll the SPI interface to see whether data is available, without dedicating a GPIO pin from the host
processor to the TSC2301 DAV pin. This bit is normally high, goes low when touch screen or keypad data is
available, and is reset high when all the new data has been read. When written to, this bit becomes KBC1,
operation detailed below.
Table 24. SPI Data Available (Read Only)
SDAV
Description
0
Touchscreen data is available.
1
No new data available (default)
Bits [15:14] — KBC1-KBC0 (write mode)
KBIRQ Control (write-only mode). These bits control the behavior of the KBIRQ signal. There are four possible
ways to de-assert the KBIRQ signal once it goes low. These bits control which particular events cause the
KBIRQ signal to be de-asserted (go high). The four de-assertion possibilities are:
A. Hardware or software reset. Hardware reset—RESET pin asserted (high) and subsequently de-asserted.
Software reset—writing BB00h to register 04h, page 1.
B. Writing 1 to the SCS bit. Bit 14 of register 01h, page 1
C. Releasing the pressed key on the keypad.
D. Reading the keypad data register (register 04h, page0).
Refer to the table below to see which settings of the KBC1 - KBC0 correspond to the KBIRQ reset events. When
read, KBC1 becomes SDAV operation detailed above. KBC0 operates the same as in read and write modes.
Table 25. KBIRQ Behavior Possibilities
KBC1 KBC0 KBIRQ Reset Event
0
De-assertion possibility A or B or C.
0
1
De-assertion possibility A or B.
1
0
De-assertion possibility A or B or C or D.
1
De-assertion possibility A or B or D (default).
PLL Output on GPIO_0. This bit allows the user to receive the output of the audio codec internal PLL. This bit is
provided so the host processor can use the output of the PLL, to generate its I2S signals in sync with an external
MCLK or crystal oscillator. Writing a 0 to this bit connects the output of the PLL to the GPIO_0 pin. Otherwise,
the GPIO_0 pin operates as normal.
Table 26. PLL Output
PLLO
Description
0
Output PLL on GPIO_0.
1
GPIO_0 operates as normal (default).
37
相關PDF資料
PDF描述
TSC2302IRGZRG4 SPECIALTY CONSUMER CIRCUIT, PQCC48
TSDC4872IJT 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8
TS4872IJT 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8
TSH103ID 3 CHANNEL, VIDEO AMPLIFIER, PDSO8
TSH103IDT 3 CHANNEL, VIDEO AMPLIFIER, PDSO8
相關代理商/技術參數
參數描述
TSC2301IZQZ 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
TSC2301IZQZR 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/20-Bit Stereo Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
TSC2301PAG 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC
TSC2301PAGR 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC
TSC2302 制造商:BB 制造商全稱:BB 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC
主站蜘蛛池模板: 深圳市| 丰城市| 安塞县| 新营市| 龙游县| 张家港市| 龙岩市| 南京市| 万州区| 元谋县| 巴彦县| 瑞安市| 巴林左旗| 沙河市| 龙南县| 大埔区| 甘肃省| 阿勒泰市| 犍为县| 汝阳县| 宁远县| 稷山县| 岑溪市| 博湖县| 夏邑县| 塔河县| 根河市| 阳山县| 察哈| 武鸣县| 英吉沙县| 望江县| 洱源县| 阿勒泰市| 呈贡县| 潢川县| 宁远县| 常德市| 偏关县| 清原| 北宁市|