- 您現在的位置：買賣IC網 > PDF目錄373920 > AD7851 (Analog Devices, Inc.) 14-Bit 333 kSPS Serial A/D Converter PDF資料下載
參數資料
| 型號： | AD7851 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 14-Bit 333 kSPS Serial A/D Converter |
| 中文描述： | 14位333 kSPS的串行A / D轉換器 |
| 文件頁數： | 10/36頁 |
| 文件大小： | 435K |
| 代理商： | AD7851 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD7851
–10–
REV. A
CONT ROL RE GIST E R
T he arrangement of the control register is shown below. T he control register is a write only register and contains 14 bits of data. T he
control register is selected by putting two 1s in ADDR1 and ADDR0. T he function of the bits in the control register are described
below. T he power-up status of all bits is 0.
MSB
ZERO
ZERO
ZERO
ZERO
PMGT 1
PMGT 0
PMGT 1
RDSL T 0
2/
3
MODE
C ONVST
C AL MD
C AL ST 1
C AL SL T 0
ST C AL
L SB
Control Register Bit Function Description
Bit
Mnemonic
Comment
13
12
11
10
9
8
7
6
5
ZERO
ZERO
ZERO
ZERO
PMGT 1
PMGT 0
RDSLT 1
RDSLT 0
2/
3
MODE
T hese four bits must be set to 0 when writing to the control register.
Power Management Bits. T hese two bits are used with the
SLEEP
pin for putting the part into various
power-down modes (see Power-Down section for more details).
T heses two bits determine which register is addressed for the read operations. See T able II.
Interface Mode Select Bit. With this bit set to 0, Interface Mode 2 is enabled. With this bit set to 1,
Interface Mode 1 is enabled where DIN is used as an output as well as an input. T his bit is set to 0 by
default after every read cycle; thus when using Interface Mode 1, this bit needs to be set to 1 in every
write cycle.
Conversion Start Bit. A logic one in this bit position starts a single conversion, and this bit is automati-
cally reset to 0 at the end of conversion. T his bit may also used in conjunction with system calibration
(see Calibration section on page 21).
Calibration Mode Bit. A 0 here selects self-calibration and a 1 selects a system calibration (see T able III).
Calibration Selection Bits and Start Calibration Bit. T hese bits have two functions.
With the ST CAL bit set to 1, the CALSLT 1 and CALSLT 0 bits determine the type of calibration per-
formed by the part (see T able III). T he ST CAL bit is automatically reset to 0 at the end of calibration.
With the ST CAL bit set to 0, the CALSLT 1 and CALSLT 0 bits are decoded to address the calibration
register for read/write of calibration coefficients (see section on the calibration registers for more details).
4
CONVST
3
2
1
0
CALMD
CALSLT 1
CALSLT 0
ST CAL
T able III. Calibration Selection
CALMD
CALSLT 1
CALSLT 0
Calibration T ype
0
0
0
A
full internal calibration
is initiated where the internal DAC is calibrated followed by the
internal gain error and finally the internal offset error is calibrated out. T his is the default setting.
Here the
internal gain error
is calibrated out followed by the
internal offset error
calibrated
out.
T his calibrates out the
internal offset error
only.
T his calibrates out the
internal gain error
only.
A
full system calibration
is initiated here where first the internal DAC is calibrated, fol-
lowed by the system gain error, and finally the system offset error is calibrated out.
Here the
system gain error
is calibrated out followed by the
system offset error
.
T his calibrates out the
system offset error
only.
T his calibrates out the
system gain error
only.
0
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| AD7851AN | 14-Bit 333 kSPS Serial A/D Converter |
| AD7851AR | 14-Bit 333 kSPS Serial A/D Converter |
| AD7851ARS | 14-Bit 333 kSPS Serial A/D Converter |
| AD7851KN | 14-Bit 333 kSPS Serial A/D Converter |
| AD7851KR | 14-Bit 333 kSPS Serial A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7851AN | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:14 BIT SELF CALIBRATION ADC I.C. - Bulk |
| AD7851ANZ | 功能描述:IC ADC 14BIT SRL 333KSPS 24-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7851AR | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:14 BIT SELF CALIBRATION ADC I.C. - Bulk |
| AD7851AR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W T/R |
| AD7851ARS | 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP 制造商:Analog Devices 功能描述:IC 14-BIT ADC |
發布緊急采購，3分鐘左右您將得到回復。