- 您現在的位置：買賣IC網 > PDF目錄373963 > AD9446-80LVDS (Analog Devices, Inc.) 16-Bit, 80/100 MSPS ADC PDF資料下載
參數資料
| 型號： | AD9446-80LVDS |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 16-Bit, 80/100 MSPS ADC |
| 中文描述： | 16位，80/100 MSPS的模數轉換器 |
| 文件頁數： | 9/36頁 |
| 文件大小： | 952K |
| 代理商： | AD9446-80LVDS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9446
TERMINOLOGY
Analog Bandwidth (Full Power Bandwidth)
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Rev. 0 | Page 9 of 36
Aperture Delay (t
A
)
The delay between the 50% point of the rising edge of the clock
and the instant at which the analog input is sampled.
Aperture Uncertainty (Jitter, t
J
)
The sample-to-sample variation in aperture delay.
Clock Pulse Width and Duty Cycle
Pulse width high is the minimum amount of time that the
clock pulse should be left in the Logic 1 state to achieve rated
performance. Pulse width low is the minimum time the clock
pulse should be left in the low state. At a given clock rate, these
specifications define an acceptable clock duty cycle.
Differential Nonlinearity (DNL, No Missing Codes)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 16-bit resolution indicates that all 65,536
codes must be present over all operating ranges.
Effective Number of Bits (ENOB)
The effective number of bits for a sine wave input at a given
input frequency can be calculated directly from its measured
SINAD using the following formula:
(
)
6.02
1.76
=
SINAD
ENOB
Gain Error
The first code transition should occur at an analog value of
LSB above negative full scale. The last transition should occur
at an analog value of 1 LSB below the positive full scale. Gain
error is the deviation of the actual difference between first and
last code transitions and the ideal difference between first and
last code transitions.
Integral Nonlinearity (INL)
The deviation of each individual code from a line drawn from
negative full scale through positive full scale. The point used as
negative full scale occurs LSB before the first code transition.
Positive full scale is defined as a level 1 LSB beyond the last
code transition. The deviation is measured from the middle of
each particular code to the true straight line.
Maximum Conversion Rate
The clock rate at which parametric testing is performed.
Minimum Conversion Rate
The clock rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Offset Error
The major carry transition should occur for an analog value of
LSB below VIN+ = VIN. Offset error is defined as the
deviation of the actual transition from that point.
Out-of-Range Recovery Time
The time it takes for the ADC to reacquire the analog input
after a transition from 10% above positive full scale to 10%
above negative full scale, or from 10% below negative full scale
to 10% below positive full scale.
Output Propagation Delay (t
PD
)
The delay between the clock rising edge and the time when all
bits are within valid logic levels.
Power-Supply Rejection Ratio
The change in full scale from the value with the supply at the
minimum limit to the value with the supply at the maximum
limit.
Signal-to-Noise and Distortion (SINAD)
The ratio of the rms input signal amplitude to the rms value of
the sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc.
Signal-to-Noise Ratio (SNR)
The ratio of the rms input signal amplitude to the rms value of
the sum of all other spectral components below the Nyquist
frequency, excluding the first six harmonics and dc.
Spurious-Free Dynamic Range (SFDR)
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious component
may be a harmonic. SFDR can be reported in dBc (that is, degrades
as signal level is lowered) or dBFS (always related back to converter
full scale).
Temperature Drift
The temperature drift for offset error and gain error specifies
the maximum change from the initial (25°C) value to the value
at T
MIN
or T
MAX
.
Total Harmonic Distortion (THD)
The ratio of the rms input signal amplitude to the rms value of
the sum of the first six harmonic components.
Two-Tone SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9446-80PCB | 16-Bit, 80/100 MSPS ADC |
| AD9480 | 8-Bit, 250 MSPS 3.3 V A/D Converter |
| AD9480-LVDS-PCB3 | 8-Bit, 250 MSPS 3.3 V A/D Converter |
| AD9480ASUZ-2501 | 8-Bit, 250 MSPS 3.3 V A/D Converter |
| AD9480BSUZ-2501 | 8-Bit, 250 MSPS 3.3 V A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9446-80LVDS/PCB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT, 80/100 MSPS ADC - Bulk |
| AD9446-80LVDS/PCBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9446-80 制造商:Analog Devices 功能描述:16-BIT 180MSPS ADC EVAL BD - Bulk |
| AD9446-80LVDSPCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed ADC USB FIFO Evaluation Kit |
| AD9446-80PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 80/100 MSPS ADC |
| AD9446BSVZ-100 | 功能描述:模數轉換器 - ADC 16Bit 100 MSPS ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。