- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9876 (Analog Devices, Inc.) Broadband Modem Mixed-Signal Front End PDF資料下載
參數資料
| 型號： | AD9876 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 模擬前端 |
| 英文描述： | Broadband Modem Mixed-Signal Front End |
| 中文描述： | 寬帶調制解調器混合信號前端 |
| 文件頁數： | 24/24頁 |
| 文件大小： | 666K |
| 代理商： | AD9876 |
REV. A
–24–
C
P
AD9876
on the MxFE side of the ferrite as well as a low ESR, ESL
decoupling capacitors on each supply pin (i.e., the AD9876
requires five power supply decoupling caps, one each on Pins 5,
38, 47, 14, and 35). The decoupling caps should be placed as close
to the MxFE supply pins as possible. An example of the proper
decoupling is shown in the AD9876 evaluation board schematic.
Ground Planes
In general, if the component placing guidelines discussed earlier
can be implemented, it is best to have at least one continuous
ground plane for the entire board. All ground connections should be
made as short as possible. This will result in the lowest impedance
return paths and the quietest ground connections.
If the components cannot be placed in a manner that will keep the
high frequency ground currents from traversing under the MxFE
and analog components, it may be necessary to put current steering
channels into the ground plane to route the high frequency
currents around these sensitive areas. These current
steering
channels should be made only when and where necessary.
Signal Routing
The digital Rx and Tx signal paths should be kept as short as
possible. Also, the impedance of these traces should have
a controlled characteristic impedance of about 50
. This will
prevent poor signal integrity and the high currents that can
occur during undershoot or overshoot caused by ringing. If the
signal traces cannot be kept shorter than about 1.5 inches, series
termination resistors (33
to 47
) should be placed close to
all signal sources. It is a good idea to series-terminate all clock
signals at their source, regardless of trace length.
The receive Rx and Rx signals are the most sensitive
signals on the entire board. Careful routing of these signals
is essential for good receive path performance. The Rx and
Rx signals form a differential pair and should be routed
together as a pair. By keeping the traces adjacent to each other,
noise coupled onto the signals will appear as common mode and
will be largely rejected by the MxFE receive input. Keeping the
driving point impedance of the receive signal low and placing
any low-pass filtering of the signals close to the MxFE will
further reduce the possibility of noise corrupting these signals.
OUTLINE DIMENSIONS
48-Lead Plastic Quad Flatpack [LQFP]
1.4 mm Thick
(ST-48)
Dimensions shown in millimeters
(PINS DOWN)
1
12
13
25
24
36
37
48
0.27
0.22
0.17
0.50
BSC
7.00
BSC
SEATING
PLANE
1.60 MAX
0.75
0.60
0.45
VIEW A
7
3.5
0
0.20
0.09
1.45
1.40
1.35
0.15
0.05
0.08 MAX
COPLANARITY
VIEW A
ROTATED 90 CCW
PIN 1
INDICATOR
9.00 BSC
COMPLIANT TO JEDEC STANDARDS MS-026BBC
SEATING
PLANE
Revision History
Location
Page
10/02—Data Sheet changed from REV. 0 to REV. A.
Changes to to Table IV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Changes to REGISTER 3—CLOCK SOURCE CONFIGURATION section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
相關PDF資料 |
PDF描述 |
|---|---|
| AD9876-EB | Broadband Modem Mixed-Signal Front End |
| AD9876BST | Broadband Modem Mixed-Signal Front End |
| AD9876BSTRL | Broadband Modem Mixed-Signal Front End |
| AD9877 | Mixed-Signal Front End Set-Top Box, Cable Modem |
| AD9877ABS | Mixed-Signal Front End Set-Top Box, Cable Modem |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9876ABST | 制造商:Rochester Electronics LLC 功能描述:12B BROADBAND MODEM MXFE CONVERTER - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD9876ABSTRL | 制造商:Rochester Electronics LLC 功能描述:12B BROADBAND MODEM MXFE CONVERTER - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD9876BST | 制造商:Analog Devices 功能描述:Modem Chip Single 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:12B BROADBAND MODEM MXFE CONVERTER - Bulk |
| AD9876BSTRL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| AD9876EB | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。