欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD9882KST-100
廠商: ANALOG DEVICES INC
元件分類: 消費家電
英文描述: Dual Interface for Flat Panel Displays
中文描述: SPECIALTY CONSUMER CIRCUIT, PQFP100
封裝: PLASTIC, MS-026BED, LQFP-100
文件頁數: 10/36頁
文件大小: 370K
代理商: AD9882KST-100
REV. A
–10–
AD9882
PIN FUNCTION DETAIL (ANALOG INTERFACE)
INPUTS
R
AIN
Analog Input for RED Channel
G
AIN
Analog Input for GREEN Channel
B
AIN
Analog Input for BLUE Channel
High impedance inputs that accept the RED,
GREEN, and BLUE channel graphics signals,
respectively. For RGB, the three channels are
identical and can be used for any colors, but
colors are assigned for convenient reference.
For proper 4:2:2 formatting in a YPbPr application,
the Y must be connected to the G
AIN
input, the
Pb must be connected to the B
AIN
input, and the
Pr must be connected to the R
AIN
input.
They accommodate input signals ranging from
0.5 V to 1.0 V full scale. Signals should be
ac-coupled to these pins to support clamp
operation.
HSYNC
Horizontal Sync Input
This input receives a logic signal that establishes
the horizontal timing reference and provides the
frequency reference for pixel clock generation.
The logic sense of this pin is controlled by Serial
Register Bit 10H, Bit 6 (Hsync Polarity). Only
the leading edge of Hsync is active; the trailing
edge is ignored. When Hsync Polarity = 0, the
falling edge of Hsync is used. When Hsync
Polarity = 1, the rising edge is active.
The input includes a Schmitt trigger for noise
immunity, with a nominal input threshold of
1.5 V.
Electrostatic Discharge (ESD) protection diodes
will conduct heavily if this pin is driven more
than 0.5 V above the maximum tolerance voltage
(3.3 V), or more than 0.5 V below ground.
VSYNC
Vertical Sync Input
This is the input for vertical sync.
SOGIN
Sync-on-Green Input
This input is provided to assist with processing
signals with embedded sync, typically on the
GREEN channel. The pin is connected to a
high speed comparator with an internally gener-
ated threshold, which is set by the value of
register 0FH, Bits 7
3.
When connected to an ac-coupled graphics
signal with embedded sync, it will produce a
noninverting digital output on SOGOUT.
When not used, this input should be left uncon-
nected. For more details on this function and
how it should be configured, refer to the Sync-
on-Green section.
SOGOUT
Sync-on-Green Slicer Output
This pin can be programmed to produce either
the output from the Sync-on-Green slicer com-
parator or an unprocessed but delayed version of
the Hsync input. See the Sync Processing Block
Diagram, Figure 18, to view how this pin is
connected.
Note: The output from this pin is the composite
SYNC without additional processing from the
AD9882.
External Filter Connection
For proper operation, the pixel clock generator
PLL requires an external filter. Connect the
filter shown in Figure 6 to this pin. For optimal
performance, minimize noise and parasitics on
this node.
REFBYPASS Internal Reference BYPASS
Bypass for the internal 1.25 V band gap refer-
ence. It should be connected to ground through
a 0.1
m
F capacitor.
The absolute accuracy of this reference is
±
4%,
and the temperature coefficient is
±
50 ppm,
which is adequate for most AD9882 applica-
tions. If higher accuracy is required, an external
reference may be employed instead.
MIDBYPASS Midscale Voltage Reference BYPASS
Bypass for the internal midscale voltage refer-
ence. It should be connected to ground through
a 0.1
m
F capacitor. The exact voltage varies with
the gain setting of the RED channel.
HSOUT
Horizontal Sync Output
A reconstructed and phase-aligned version of
the Hsync input. The duration of Hsync can
only be programmed on the analog interface,
not the digital.
DATACK
Data Output Clock
The data clock output signal is used to clock the
output data and HSOUT into external logic.
It is produced by the internal clock generator
and is synchronous with the internal pixel
sampling clock.
When the sampling time is changed by adjusting
the PHASE register, the output timing is shifted
as well. The Data, DATACK, and HSOUT
outputs are all moved so the timing relationship
among the signals is maintained.
VSOUT
Vertical Sync Output
The separated Vsync from a composite signal or
a direct pass-through of the Vsync input. The
polarity of this output can be controlled via
Register 10H, Bit 2. The placement and duration
in all modes is set by the graphics transmitter.
FILT
相關PDF資料
PDF描述
AD9882KST-140 Dual Interface for Flat Panel Displays
AD9882 Dual Interface for Flat Panel Displays
AD9883ABST-RL140 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays
AD9883AKST-110 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays
AD9883AKST-140 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays
相關代理商/技術參數
參數描述
AD9882KST-140 制造商:Analog Devices 功能描述:Interface for Flat Panel Display 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:LOW COST DUAL INTERFACE - Bulk 制造商:Analog Devices 功能描述:IC DUAL INTERFACE
AD9882KSTZ-100 功能描述:IC INTERFACE/DVI 100MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9882KSTZ-140 功能描述:IC INTERFACE/DVI 100MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9883 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS Analog Interface for Flat Panel Displays
AD9883/PCB 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS Analog Interface for Flat Panel Displays
主站蜘蛛池模板: 哈巴河县| 兰西县| 教育| 深水埗区| 纳雍县| 苍溪县| 特克斯县| 左贡县| 临江市| 驻马店市| 榆林市| 壶关县| 建昌县| 太湖县| 新河县| 大城县| 新丰县| 潜山县| 施甸县| 梨树县| 长白| 北流市| 海门市| 南木林县| 鹤庆县| 庆元县| 安塞县| 布尔津县| 泰和县| 白水县| 巴马| 监利县| 咸丰县| 萨迦县| 大足县| 柳江县| 奉贤区| 平遥县| 雅江县| 胶南市| 志丹县|