- 您現在的位置：買賣IC網 > PDF目錄373971 > AD9948 (Analog Devices, Inc.) 10-Bit CCD Signal Processor with Precision Timing⑩ Core PDF資料下載
參數資料
| 型號： | AD9948 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 10-Bit CCD Signal Processor with Precision Timing⑩ Core |
| 中文描述： | 10位CCD信號處理器核心精確定時⑩ |
| 文件頁數： | 24/28頁 |
| 文件大小： | 539K |
| 代理商： | AD9948 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
REV. 0
–24–
AD9948
3V
ANALOG
SUPPLY
SERIAL
INTERFACE
3
CCD SIGNAL
VD/HD/HBLK INPUTS
CLP/BLK OUTPUT
4
3V
DRIVER
SUPPLY
RG DRIVER
SUPPLY
H DRIVER
SUPPLY
MASTER CLOCK INPUT
3V
ANALOG
SUPPLY
DATA
OUTPUTS
10
H1–H4
4
TOP VIEW
AD9948
PIN 1
30 REFB
29 REFT
28 AVSS
27 CCDIN
26 AVDD
25 CLI
24 TCVDD
23 TCVSS
22 RGVDD
21 RG
NC 1
D1 3
D2 4
DRVDD 6
D3 7
D4 8
D5 9
D6 10
4
3
3
3
3
3
3
3
3
3
D
D
H
H
H
H
H
H
R
RG OUTPUT
+
+
+
+
DRVSS 5
(LSB) D0 2
4.7 F 0.1 F
0.1 F
4.7 F
4.7 F
0.1 F
0.1 F
4.7 F
0.1 F
0.1 F
0.1 F
1 F
1 F
Figure 21. Recommended Circuit Configuration
APPLICATIONS INFORMATION
Circuit Configuration
The AD9948 recommended circuit configuration is shown in
Figure 21. Achieving good image quality from the AD9948
requires careful attention to PCB layout. All signals should be
routed to maintain low noise performance. The CCD output
signal should be directly routed to Pin 27 through a 0.1
μ
F
capacitor. The master clock CLI should be carefully routed to
Pin 25 to minimize interference with the CCDIN, REFT, and
REFB signals.
The digital outputs and clock inputs are located on Pins 2 to 13
and Pins 31 to 39, and should be connected to the digital ASIC
away from the analog and CCD clock signals. Placing series
resistors close to the digital output pins may help to reduce
digital code transition noise. If the digital outputs must drive a
load larger than 20 pF, buffering is recommended to minimize
additional noise. If the digital ASIC can accept gray code, the
AD9948’s outputs can be selected to output data in gray code
format using the control register Bit D5. Gray coding will
help reduce potential digital transition noise compared with
binary coding.
The H1–H4 and RG traces should have low inductance to
avoid excessive distortion of the signals. Heavier traces are
recommended because of the large transient current demand
on H1–H4 from the capacitive load of the CCD. If possible,
physically locating the AD9948 closer to the CCD will reduce
the inductance on these lines. As always, the routing path
should be as direct as possible from the AD9948 to the CCD.
Grounding and Decoupling Recommendations
As shown in Figure 21, a single ground plane is recommended
for the AD9948. This ground plane should be as continuous as
possible, particularly around Pins 23 to 30. This will ensure that
all analog decoupling capacitors provide the lowest possible
impedance path between the power and bypass pins and their
respective ground pins. All high frequency decoupling capacitors
should be located as close as possible to the package pins. It is
recommended that the exposed paddle on the bottom of the
package be soldered to a large pad, with multiple vias connect-
ing the pad to the ground plane.
All the supply pins must be decoupled to ground with good
quality, high frequency chip capacitors. There should also be a
4.7
μ
F or larger bypass capacitor for each main supply—AVDD,
RGVDD, HVDD, and DRVDD—although this is not necessary
for each individual pin. In most applications, it is easier to share
the supply for RGVDD and HVDD, which may be done as long
as the individual supply pins are separately bypassed. A separate
3 V supply may be used for DRVDD, but this supply pin should
still be decoupled to the same ground plane as the rest of the
chip. A separate ground for DRVSS is not recommended.
The reference bypass pins (REFT, REFB) should be decoupled
to ground as close as possible to their respective pins. The analog
input (CCDIN) capacitor should also be located close to the pin.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9948KCP | 10-Bit CCD Signal Processor with Precision Timing⑩ Core |
| AD9948KCPRL | 10-Bit CCD Signal Processor with Precision Timing⑩ Core |
| AD9949KCP | 12-Bit CCD Signal Processor with Precision Timing Core |
| AD9949 | 12-Bit CCD Signal Processor with Precision Timing Core |
| AD9949KCPZRL | 12-Bit CCD Signal Processor with Precision Timing Core |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9948AKCPZ | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
| AD9948AKCPZRL | 制造商:Analog Devices 功能描述: |
| AD9948KCP | 制造商:Rochester Electronics LLC 功能描述:10 BIT 25 MSPS, 3V ANALOG FRONT END - Bulk 制造商:Analog Devices 功能描述: |
| AD9948KCPRL | 制造商:Rochester Electronics LLC 功能描述:10 BIT 25 MSPS, 3V ANALOG FRONT END - Bulk 制造商:Analog Devices 功能描述: |
| AD9948KCPZ | 功能描述:IC CCD SIGNAL PROCESSOR 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。