- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1027ARQZ-RL7 (ON Semiconductor)IC REMOTE THERMAL CTLR 24QSOP Datasheet資料下載
參數資料
| 型號： | ADM1027ARQZ-RL7 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 10/56頁 |
| 文件大小： | 1822K |
| 描述： | IC REMOTE THERMAL CTLR 24QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation Notice 25/Aug/2008 Product Obsolescence 30/Sept/2009 |
| 標準包裝： | 1,000 |
| 系列： | dBCool® |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 105°C，外部傳感器 |
| 精確度： | ±1°C |
| 拓撲： | ADC，比較器，風扇速度計數器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 無 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
REV. A
10
ADM1027
Notes
1. It is possible to read a data byte from a data register without
first writing to the address pointer register if the address
pointer register is already at the correct value. However, it is
not possible to write data to a register without writing to the
address pointer register, because the first data byte of a write
is always written to the address pointer register.
2. In Figures 6 to 8, the serial bus address is shown as the default
value 01011(A1)(A0), where A1 and A0 are set by the address
select mode function previously defined.
3. In addition to supporting the send byte and receive byte
protocols, the ADM1027 also supports the read byte protocol
(see System Management Bus specifications Rev. 2.0 for
more information).
4. If it is required to perform several read or write operations in
succession, the master can send a repeat start condition instead
of a stop condition to begin a new operation.
ADM1027 WRITE OPERATIONS
The SMBus specification defines several protocols for different
types of read and write operations. The ones used in the
ADM1027 are discussed below. The following abbreviations are
used in the diagrams:
S START
P STOP
R READ
W WRITE
A ACKNOWLEDGE
A NO ACKNOWLEDGE
The ADM1027 uses the following SMBus write protocols:
Send Byte
In this operation, the master device sends a single command
byte to a slave device, as follows:
1. The master device asserts a start condition on SDA.
2. The master sends the 7-bit slave address followed by the
write bit (low).
3. The addressed slave device asserts ACK on SDA.
4. The master sends a command code.
5. The slave asserts ACK on SDA.
6. The master asserts a stop condition on SDA and the
transaction ends.
For the ADM1027, the send byte protocol is used to write a
register address to RAM for a subsequent single byte read from
the same address. This is illustrated in Figure 9.
S
SLAVE
ADDRESS
W A
A P
1
2
3
4
5 6
REGISTER
ADDRESS
Figure 9. Setting a Register Address for Subsequent Read
If it is required to read data from the register immediately after
setting up the address, the master can assert a repeat start con-
dition immediately after the final ACK and carry out a single
byte read without asserting an intermediate stop condition.
Write Byte
In this operation, the master device sends a command byte and
one data byte to the slave device, as follows:
1. The master device asserts a start condition on SDA.
2. The master sends the 7-bit slave address followed by the
write bit (low).
3. The addressed slave device asserts ACK on SDA.
4. The master sends a command code.
5. The slave asserts ACK on SDA.
6. The master sends a data byte.
7. The slave asserts ACK on SDA.
8. The master asserts a stop condition on SDA to end the
transaction.
This is illustrated in Figure 10.
S
SLAVE
ADDRESS
W A
1
2
3
4
5
6
A
DATA
A P
7 8
REGISTER
ADDRESS
Figure 10. Single Byte Write to a Register
ADM1027 READ OPERATIONS
The ADM1027 uses the following SMBus read protocols:
Receive Byte
This is useful when repeatedly reading a single register. The
register address needs to have been set up previously. In this
operation, the master device receives a single byte from a slave
device, as follows:
1. The master device asserts a start condition on SDA.
2. The master sends the 7-bit slave address followed by the
read bit (high).
3. The addressed slave device asserts ACK on SDA.
4. The master receives a data byte.
5. The master asserts NO ACK on SDA.
6. The master asserts a stop condition on SDA and the trans-
action ends.
In the ADM1027, the receive byte protocol is used to read a
single byte of data from a register whose address has previously
been set by a send byte or write byte operation.
S
SLAVE
ADDRESS
R A
DATA A
P
1
2
3
4
5 6
Figure 11. Single Byte Read from a Register
Alert Response Address
Alert Response Address (ARA) is a feature of SMBus devices,
which allows an interrupting device to identify itself to the host
when multiple devices exist on the same bus.
The SMBALERT output can be used as an interrupt output or
can be used as an SMBALERT. One or more outputs can be
connected to a common SMBALERT line connected to the
master. If a devices SMBALERT line goes low, the following
procedure occurs:
1. SMBALERT is pulled low.
2. Master initiates a read operation and sends the alert response
address (ARA = 0001 100). This is a general call address that
must not be used as a specific device address.
3. The device whose SMBALERT output is low responds to
the alert response address, and the master reads its device
address. The address of the device is now known and it can
be interrogated in the usual way.
4. If more than one devices SMBALERT output is low, the one
with the lowest device address will have priority, in accordance
with normal SMBus arbitration.
Rev. 3 | Page 10 of 56 | www.onsemi.com
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1029ARQZ-R7 | IC SENSOR 2TEMP/FAN CTRL 24QSOP |
| ADM1030ARQZ-RL7 | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1027ARQZ-RL71 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOLa?￠ Remote Thermal Controller and Voltage Monitor |
| ADM1028 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Remote Thermal Diode Monitor with Linear Fan Control |
| ADM1028ARQ | 功能描述:IC SENSOR TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1028ARQ-REEL7 | 制造商:Rochester Electronics LLC 功能描述:TDM + LINEAR FAN CONTROL I.C. - Tape and Reel |
| ADM1029 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PWM Fan Controller and Temperature Monitor for High Availability Systems |
發布緊急采購，3分鐘左右您將得到回復。