- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1027ARQZ-RL7 (ON Semiconductor)IC REMOTE THERMAL CTLR 24QSOP Datasheet資料下載
參數資料
| 型號： | ADM1027ARQZ-RL7 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 28/56頁 |
| 文件大小： | 1822K |
| 描述： | IC REMOTE THERMAL CTLR 24QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation Notice 25/Aug/2008 Product Obsolescence 30/Sept/2009 |
| 標準包裝： | 1,000 |
| 系列： | dBCool® |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 105°C，外部傳感器 |
| 精確度： | ±1°C |
| 拓撲： | ADC，比較器，風扇速度計數器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 無 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
REV. A
28
ADM1027
Step 1
Determine the Hardware Configuration
Essentially this means choosing whether to use Pin 10 as a PWM2
output or as an SMBALERT output and deciding which SMBus
address is to be used. To set Pin 10 as SMBALERT, set Bit 0
of Configuration Register 3 (Addr = 0x78) equal to 1. The
default state is PWM2, where this bit equals 0.
It also refers to the layout recommendations of the ADM1027
on a motherboard, for example.
ADM1027 Placement Considerations
Motherboards are electrically noisy environments, and care must
be taken to protect the analog inputs from noise, particularly the
D+/D lines of a remote diode sensor. The following precautions
should be taken:
1. Place the ADM1027 as close as possible to the remote sensing
diode. Provided that the worst noise sources such as clocks
and data/address buses are avoided, this distance can be
4 inches to 8 inches.
2. Route the D+ and D tracks close together, in parallel, with
grounded guard tracks on each side. Provide a ground plane
under the tracks if possible. Do NOT run the D+/D lines in
different directions.
3. Use wide tracks to minimize inductance and reduce noise
pickup. A 10 mil track minimum width and spacing is
recommended.
4. Try to minimize the number of copper/solder joints, which
can cause thermocouple effects. Where copper/solder joints
are used, make sure that they are in both the D+ and D
path and at the same temperature. Avoid routing D+/D
on multiple layers or through vias if possible. These increase
series resistance that will cause temperature error.
5. Place a 0.1 mF supply bypass capacitor close to the ADM1027.
6. If the distance to the remote sensor is more than 8 inches,
the use of shielded twisted pair cable is recommended. This
will work up to 100 feet. Connect the twisted pair to D+/D
and the shield to GND close to the ADM1027. Leave the
remote end of the shield unconnected to avoid ground loops.
Because the measurement technique uses switched current
sources, excessive cable (adds resistance) and/or filter capacitance
can affect the measurement. A 1 W series resistance introduces
about 0.8
o
C error.
Rev. 3 | Page 28 of 56 | www.onsemi.com
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1029ARQZ-R7 | IC SENSOR 2TEMP/FAN CTRL 24QSOP |
| ADM1030ARQZ-RL7 | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1027ARQZ-RL71 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOLa?￠ Remote Thermal Controller and Voltage Monitor |
| ADM1028 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Remote Thermal Diode Monitor with Linear Fan Control |
| ADM1028ARQ | 功能描述:IC SENSOR TEMP/FAN CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1028ARQ-REEL7 | 制造商:Rochester Electronics LLC 功能描述:TDM + LINEAR FAN CONTROL I.C. - Tape and Reel |
| ADM1029 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PWM Fan Controller and Temperature Monitor for High Availability Systems |
發布緊急采購，3分鐘左右您將得到回復。