- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC836BS (ANALOG DEVICES INC) MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU PDF資料下載
參數資料
| 型號： | ADUC836BS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| 中文描述： | 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | 14 X 14 MM, MO-022-AC-1, MQFP-52 |
| 文件頁數： | 54/80頁 |
| 文件大小： | 5913K |
| 代理商： | ADUC836BS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
ADuC836
–54–
TIMER/COUNTER 0 AND 1 OPERATING MODES
The following paragraphs describe the operating modes for Timer/
Counters 0 and 1. Unless otherwise noted, it should be assumed
that these modes of operation are the same for both Timer 0 and 1.
Mode 0 (13-Bit Timer/Counter)
Mode 0 configures an 8-bit timer/counter with a divide-by-32
prescaler. Figure 48 shows Mode 0 operation.
12
CORE
CLK
*
CONTROL
P3.4/T0
GATE
P3.2/
INT0
TR0
TF0
TL0
(5 BITS)
TH0
(8 BITS)
INTERRUPT
C/
T
= 0
*
THE CORE CLOCK IS THE OUTPUT OF THE PLL (SEE THE ON-CHIP PLL SECTION)
C/
T
= 1
Figure 48. Timer/Counter 0, Mode 0
In this mode, the timer register is configured as a 13-bit register.
As the count rolls over from all 1s to all 0s, it sets the timer over-
flow flag. The overflow flag, TF0, can then be used to request an
interrupt. The counted input is enabled to the timer when TR0 = 1
and either Gate = 0 or
INT0
= 1. Setting Gate = 1 allows the
timer to be controlled by external input
INT0
to facilitate pulse-
width measurements. TR0 is a control bit in the special function
register TCON; Gate is in TMOD. The 13-bit register consists
of all eight bits of TH0 and the lower five bits of TL0. The upper
three bits of TL0 are indeterminate and should be ignored. Setting
the run flag (TR0) does not clear the registers.
Mode 1 (16-Bit Timer/Counter)
Mode 1 is the same as Mode 0, except that the timer register is
running with all 16 bits. Mode 1 is shown in Figure 49.
12
CORE
CLK
*
CONTROL
P3.4/T0
GATE
P3.2/
INT0
TR0
TF0
TL0
(8 BITS)
TH0
(8 BITS)
INTERRUPT
C/
T
= 0
C/
T
= 1
*
THE CORE CLOCK IS THE OUTPUT OF THE PLL (SEE THE ON-CHIP PLL SECTION)
Figure 49. Timer/Counter 0, Mode 1
Mode 2 (8-Bit Timer/Counter with Auto Reload)
Mode 2 configures the timer register as an 8-bit counter (TL0)
with automatic reload, as shown in Figure 50. Overflow from TL0
not only sets TF0, but also reloads TL0 with the contents of TH0,
which are preset by software. The reload leaves TH0 unchanged.
CONTROL
TF0
TL0
(8 BITS)
INTERRUPT
RELOAD
TH0
(8 BITS)
12
CORE
CLK
*
P3.4/T0
GATE
P3.2/
INT0
TR0
C/
T
= 0
C/
T
= 1
*
THE CORE CLOCK IS THE OUTPUT OF THE PLL (SEE THE ON-CHIP PLL SECTION)
Figure 50. Timer/Counter 0, Mode 2
Mode 3 (Two 8-Bit Timer/Counters)
Mode 3 has different effects on Timer 0 and Timer 1. Timer 1 in
Mode 3 simply holds its count. The effect is the same as setting
TR1 = 0. Timer 0 in Mode 3 establishes TL0 and TH0 as two
separate counters. This configuration is shown in Figure 51. TL0
uses the Timer 0 control bits: C/
T
, Gate, TR0,
INT0
, and TF0.
TH0 is locked into a timer function (counting machine cycles)
and takes over the use of TR1 and TF1 from Timer 1. Thus, TH0
now controls the Timer 1 interrupt. Mode 3 is provided for appli-
cations requiring an extra 8-bit timer or counter.
When Timer 0 is in Mode 3, Timer 1 can be turned on and off by
switching it out of and into its own Mode 3, or it can still be used by
the serial interface as a baud rate generator. In fact, it can be used in
any application not requiring an interrupt from Timer 1 itself.
CONTROL
TF0
TL0
(8 BITS)
INTERRUPT
12
CORE
CLK
*
P3.4/T0
GATE
P3.2/
INT0
TR0
C/
T
= 0
C/
T
= 1
CORE
CLK/12
TF1
TH0
(8 BITS)
INTERRUPT
CORE
CLK/12
TR1
*
THE CORE CLOCK IS THE OUTPUT OF THE PLL (SEE THE ON-CHIP PLL SECTION)
Figure 51. Timer/Counter 0, Mode 3
REV. A
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC842BCP62-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC843BCP62-5 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC842BCP62-5 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC843BCP62-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC842BCP32-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC836BS | 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS)) |
| ADUC836BSZ | 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC841 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC841BCP32-5 | 制造商:Analog Devices 功能描述:MICROCONVERTER 1-CYCLE VERSION ADUC829 - Trays |
| ADUC841BCP62-3 | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 20MHZ 3.3V 56LFCSP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。