欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: EFM32-TG822F32-SK
廠商: Energy Micro
文件頁數: 75/136頁
文件大小: 0K
描述: IC MICRO KIT GECKO 48LQFP
標準包裝: 1
系列: Tiny Gecko
套件類型: 微控制器
值: 2 件 - 閃存 - 32KB
包裝: 紙板盒
安裝類型: 表面貼裝
包括封裝: 48-LQFP
其它名稱: 914-1023
...the world's most energy friendly microcontrollers
2011-02-04 - d0002_Rev1.00
43
www.energymicro.com
Note
For B, BL, CBNZ, and CBZ instructions, the value of the PC is the address of the current
instruction plus 4 bytes.
For all other instructions that use labels, the value of the PC is the address of the current
instruction plus 4 bytes, with bit[1] of the result cleared to 0 to make it word-aligned.
Your assembler might permit other syntaxes for PC-relative expressions, such as a label
plus or minus a number, or an expression of the form [PC, #number].
3.3.7 Conditional execution
Most data processing instructions can optionally update the condition flags in the Application Program
Status Register (APSR) according to the result of the operation, see Section 2.1.3.5.1 (p. 9) . Some
instructions update all flags, and some only update a subset. If a flag is not updated, the original value
is preserved. See the instruction descriptions for the flags they affect.
You can execute an instruction conditionally, based on the condition flags set in another instruction,
either:
immediately after the instruction that updated the flags
after any number of intervening instructions that have not updated the flags.
Conditional execution is available by using conditional branches or by adding condition code suffixes
to instructions. See Table 3.4 (p. 44) for a list of the suffixes to add to instructions to make them
conditional instructions. The condition code suffix enables the processor to test a condition based on
the flags. If the condition test of a conditional instruction fails, the instruction:
does not execute
does not write any value to its destination register
does not affect any of the flags
does not generate any exception.
Conditional instructions, except for conditional branches, must be inside an If-Then instruction block. See
Section 3.9.3 (p. 76) for more information and restrictions when using the IT instruction. Depending
on the vendor, the assembler might automatically insert an IT instruction if you have conditional
instructions outside the IT block.
Use the CBZ and CBNZ instructions to compare the value of a register against zero and branch on the
result.
This section describes:
3.3.7.1 The condition flags
The APSR contains the following condition flags:
N Set to 1 when the result of the operation was negative, cleared to 0 otherwise.
Z
Set to 1 when the result of the operation was zero, cleared to 0 otherwise.
C Set to 1 when the operation resulted in a carry, cleared to 0 otherwise.
V
Set to 1 when the operation caused overflow, cleared to 0 otherwise.
For more information about the APSR see Section 2.1.3.5 (p. 8) .
A carry occurs:
相關PDF資料
PDF描述
EFM32-TG222F32-SK IC MICRO KIT GECKO 48LQFP
EFM32-TG230F32-SK IC MICRO KIT GECKO 64QFN
EFM32-TG210F32-SK IC MICRO KIT GECKO 32QFN
1267 X 6" TAPE ALUMINUM FOIL 6" X 1FT
7810 0.25MM ECAP COND PAD .25MM 7.7" X 10"
相關代理商/技術參數
參數描述
EFM32TG822F32-T 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 32KB FLASH 48TQFP
EFM32TG822F8 功能描述:ARM微控制器 - MCU 8KB Flash 2KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
EFM32TG822F8-QFP48 制造商:Energy Micro AS 功能描述:TINY GECKO MCU - Tape and Reel 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 8KB FLASH 48TQFP
EFM32TG822F8-QFP48T 制造商:Energy Micro AS 功能描述:32 BIT ARM MPU, TINY GECKO - Trays
EFM32TG822F8-QFP48-T 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 8KB FLASH 48TQFP
主站蜘蛛池模板: 浙江省| 宁南县| 丰顺县| 东丰县| 卓尼县| 南投县| 平山县| 都安| 瓦房店市| 江陵县| 长宁区| 繁峙县| 岳池县| 余江县| 宜君县| 湛江市| 安徽省| 青海省| 武功县| 余干县| 自贡市| 巴林左旗| 马山县| 麟游县| 达日县| 清徐县| 石狮市| 聊城市| 桃源县| 惠东县| 锦屏县| 黎平县| 汨罗市| 江陵县| 乌拉特前旗| 淅川县| 宁城县| 都兰县| 嘉善县| 中宁县| 武夷山市|