- 您現在的位置：買賣IC網 > PDF目錄385400 > HT48RB8 (Holtek Semiconductor Inc.) 8-Bit USB Type OTP MCU PDF資料下載
參數資料
| 型號： | HT48RB8 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit USB Type OTP MCU |
| 中文描述： | 8位微控制器的USB型檢察官辦公室 |
| 文件頁數： | 23/45頁 |
| 文件大小： | 281K |
| 代理商： | HT48RB8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
HT48RB8
Rev. 1.30
23
February 10, 2003
There is a system clock control register implemented to select the clock used in the MCU. This register consists of USB
clock control bit (USBCKEN), second suspend mode control bit (SUSP2) and system clock selection (SYSCLK).
SCC
Bits
R/W
Function
2~0
Undefined bits
USBCKEN
3
R/W
USB clock control bit. When this bit is set to 1 , it indicates that the USB clock is en-
abled. Otherwise, the USB clock is turned-off. (Default= 0 )
SUSP2
4
R/W
This bit is used for decreasing power consumption in suspend mode.
In normal mode clean this bit=0 (Default= 0 )
In HALT mode set this bit=1 for decreasing power consumption.
5
R/W Undefined, should be cleared to 0
SYSCLK
6
R/W
This bit is used to specify the system oscillator frequency used by MCU. If a 6MHz
crystal oscillator or resonator is used, this bit should be set to 1 . If a 12MHz crystal
oscillator or resonator is used, this bit should be cleared to 0 (default).
7
This bit should be forced to 0
The A/D converter implemented in the MCU is a 6-channel 8-bit A/D converter. The reference voltage (high reference
voltage and low reference voltage) can be selected as coming from external pins (PB6/VRL and PB7/VRH) or internal
power supplies of MCU (VDD and VSS). The VRL and VRH are used to set the minimal and maximal boundaries of the
full-scalerangeoftheA/Dconverter.Ifananaloginputs,VRLorVRHisnotusedforA/Dconversion,italsocanbeused
as a general purpose I/O line. The ADSC (A/D converter status and control register) register is used to set the configu-
rations and A/D clock sources of A/D converter and control the operation of A/D converter.
ADSC
Bits
Function
ACS2~ACS0
2~0
These 3 bits are use to select one of eight A/D converter channels for the conversion. The
A/D converter input channels AN0~AN5 are pin-shared with PB0~PB5. PB6/VRL and
PB7/VRH are used for the A/D converter reference inputs. ACS2,ACS1,ACS0 :
000/001/010/011/100/101/110/111: AN0/AN1/AN2/AN3/AN4/AN5/VRL/VRH
ADCS1
ADCS0
4
3
A/D converter clock source selection. ADCS1,ADCS0:
00: 6MHz
01: 3MHz
10: 1.5MHz
11: 0.75MHz
START
5
StarttheA/Dconversion.(0
1
0:start,0
1:resetA/DconverterandA/Ddataregister)
ADON
6
This bit is used to control the enable/disable of A/D converter circuit. If this bit is set to 1
theA/Dconverterentersoperatingmode.Otherwise,theA/Dconverterwillbeturned-off
EOCB
7
End of A/D conversion indication. (0: end of A/D conversion)
The A/D converter data register is used to store the result of A/D conversion.
ADR
Bits
Function
D7~D0
7~0
Result of A/D conversion
相關PDF資料 |
PDF描述 |
|---|---|
| HT49C10 | 8-BIT MICROCONTROLLER |
| HT49C30L | HDSP-A101 RED DISPLAY, LED, |
| HT49R30 | DISPLAY 7 SEGMENT |
| HT49R30A-1 | DISPL 7 SEG YELLOW |
| HT49C30-1 | 8-Bit LCD Type MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT48RU80 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type 8-Bit MCU |
| HT48RXX | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Microcontroller Series |
| HT-49 | 制造商:FCI 功能描述: |
| HT49010576-5 | 制造商:Rennsteig 功能描述:HVT 1.2 TERMINALS 22-18GA |
| HT49010577-5 | 制造商:Rennsteig 功能描述:HVT 1.2 TERMINALS 18-16GA |
發布緊急采購，3分鐘左右您將得到回復。