欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HY27SS16121M
廠商: Hynix Semiconductor Inc.
英文描述: 512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
中文描述: 512兆(64Mx8bit / 32Mx16bit)NAND閃存
文件頁數: 19/43頁
文件大小: 729K
代理商: HY27SS16121M
Rev 0.6 / Oct. 2004
19
HY27SS(08/16)121M Series
HY27US(08/16)121M Series
512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
Once the erase operation has completed the Status Register can be checked for errors.
Reset
The Reset command is used to reset the Command Interface and Status Register. If the Reset command is issued dur-
ing any operation, the operation will be aborted. If it was a program or erase operation that was aborted, the contents
of the memory locations being modified will no longer be valid as the data will be partially programmed or erased.
If the device has already been reset then the new Reset command will not be accepted. The Ready/Busy signal goes
Low for t
BLBH4
after the Reset command is issued. The value of t
BLBH4
depends on the operation that the device was
performing when the command was issued, refer to Table 15 for the values.
Read Status Register
The device contains a Status Register which provides information on the current or previous Program or Erase opera-
tion. The various bits in the Status Register convey information and errors on the operation.
The Status Register is read by issuing the Read Status Register command. The Status Register information is present
on the output data bus (I/O
0
- I/O
7
) on the falling edge of Chip Enable or Read Enable, whichever occurs last. When
several memories are connected in a system, the use of Chip Enable and Read Enable signals allows the system to poll
each device separately, even when the Ready/Busy pins are common-wired. It is not necessary to toggle the Chip
Enable or Read Enable signals to update the contents of the Status Register.
After the Read Status Register command has been issued, the device remains in Read Status Register mode until
another command is issued. Therefore if a Read Status Register command is issued during a Random Read cycle a
new read command must be issued to continue with a Page Read or Sequential Row Read operation.
The Status Register bits are summarized in Table 6, Status Register Bits. Refer to Table 6 in conjunction with the fol-
lowing text descriptions.
Write Protection Bit (SR7)
The Write Protection bit can be used to identify if the device is protected or not. If the Write Protection bit is set to '1'
the device is not protected and program or erase operations are allowed. If the Write Protection bit is set to '0' the
device is protected and program or erase operations are not allowed.
Figure 17. Block Erase Operation
Block Address
Inputs
I/O
60h
Confirm
Code
D0h
SR0
Block Erase
Setup Code
Busy
tBLBH3
(Erase Busy time)
RB
70h
Read Status Register
相關PDF資料
PDF描述
HY27US08121M 512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
HY27USxxx 512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
HY27US16121M 512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
HY29F002TC-70 2 Megabit (256K x 8), 5 Volt-only, Flash Memory
HY29F002TC-45 2 Megabit (256K x 8), 5 Volt-only, Flash Memory
相關代理商/技術參數
參數描述
HY27SS16561A 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27SS16561M 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27SS561M 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27SSXXX 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
HY27UA081G1M 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
主站蜘蛛池模板: 淮北市| 卓资县| 庆云县| 大新县| 澜沧| 桓台县| 蒙阴县| 项城市| 柘荣县| 宣城市| 杭锦旗| 札达县| 河源市| 广水市| 平阳县| 鄯善县| 包头市| 蒲江县| 馆陶县| 苍山县| 北流市| 平塘县| 阜城县| 林州市| 会泽县| 香港 | 大厂| 安宁市| 嘉义县| 阿拉善盟| 崇仁县| 潮州市| 扶沟县| 凤台县| 东乌珠穆沁旗| 五指山市| 青州市| 盐城市| 元朗区| 永寿县| 冷水江市|