欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： HY27SS561M
廠商： Hynix Semiconductor Inc.
英文描述： 256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
中文描述： 片256Mbit（32Mx8bit / 16Mx16bit）NAND閃存
文件頁數： 17/44頁
文件大小： 733K
代理商： HY27SS561M
Rev 0.7 / Oct. 2004
17
HY27SS(08/16)561M Series
HY27US(08/16)561M Series
256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
Page Program
The Page Program operation is the standard operation to program data to the memory array. The main area of the
memory array is programmed by page, however partial page programming is allowed where any number of bytes (1 to
528) or words (1 to 264) can be programmed.
The max number of consecutive partial page program operations allowed in the same page is one in the main area and
two in the spare area. After exceeding this a Block Erase command must be issued before any further program opera-
tions can take place in that page.
Before starting a Page Program operation a Pointer operation can be performed to point to the area to be pro-
grammed. Refer to the Pointer Operations section and Figure 9 for details.
Each Page Program operation consists of five steps (see Figure 14):
1. one bus cycle is required to setup the Page Program command.
2. three bus cycles are then required to input the program address (refer to Table 3 and Table 4).
3. the data is then input (up to 528 Bytes/ 264 Words) and loaded into the Page Buffer.
4. one bus cycle is required to issue the confirm command to start the Program/ Erase/Read Controller.
5. The Program/ Erase/Read Controller then programs the data into the array.
Once the program operation has started the Status Register can be read using the Read Status Register command.
During program operations the Status Register will only flag errors for bits set to '1' that have not been successfully
programmed to '0'.
During the program operation, only the Read Status Register and Reset commands will be accepted, all other com-
mands will be ignored.
Once the program operation has completed the Program/ Erase/Read Controller bit SR6 is set to '1' and the Ready/
Busy signal goes High.
The device remains in Read Status Register mode until another valid command is written to the Command Interface.
Note: Before starting a Page Program operation a Pointer operation can be performed. Refer to Pointer section for details.
Figure 14. Page Program Operation
Address Inputs
I/O
80h
Page Program
Setup Code
Data Input
10h
70h
SR0
Confirm
Code
Read Status Register
Busy
tBLBH2
(Program Busy time)
RB
相關PDF資料
PDF描述
HY27US16561M 256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27US561M 256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27SS16561M 256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27US08561M 256Mbit (32Mx8bit / 16Mx16bit) NAND Flash
HY27SSxxx 512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
相關代理商/技術參數
參數描述
HY27SSXXX 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mbit (64Mx8bit / 32Mx16bit) NAND Flash
HY27UA081G1M 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27UA161G1M 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27UA1G1M 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27UAXXX 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 盐亭县| 平定县| 荣成市| 交口县| 方城县| 云和县| 六安市| 改则县| 永登县| 游戏| 辰溪县| 华蓥市| 济阳县| 定南县| 牡丹江市| 泸水县| 漳平市| 姚安县| 漳浦县| 旺苍县| 山阴县| 河南省| 巴塘县| 寿宁县| 晋江市| 什邡市| 册亨县| 黄大仙区| 达拉特旗| 苏尼特左旗| 荥阳市| 海城市| 海伦市| 宝坻区| 遵化市| 巴东县| 长岭县| 古交市| 凌云县| 大兴区| 剑川县|