- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181 (NXP Semiconductors N.V.) Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) PDF資料下載
參數資料
| 型號： | ISP1181 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| 中文描述： | 全速通用串行總線接口設備（全速通用串行總線接口器件） |
| 文件頁數： | 64/69頁 |
| 文件大小： | 1655K |
| 代理商： | ISP1181 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁
Philips Semiconductors
ISP1181
Full-speed USB interface
Objective specification
Rev. 01 — 13 March 2000
64 of 69
9397 750 06896
Philips Electronics N.V. 2000. All rights reserved.
23. Soldering
23.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering is not always suitable for surface mount ICs, or for printed-circuit boards
with high population densities. In these situations reflow soldering is often used.
23.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, infrared/convection heating in a
conveyor type oven. Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 230
°
C.
23.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
| ISP1183BS | Low-power Universal Serial Bus interface device with DMA |
| ISP1301 | Universal Serial Bus On-The-Go transceiver |
| ISP1301BS | Universal Serial Bus On-The-Go transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller |
| ISP1181ABS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller |
| ISP1181ABS,518 | 功能描述:USB 接口集成電路 USB 1.1 ADV DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181ABS,551 | 功能描述:USB 接口集成電路 USB 1.1 ADVANCED DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181ABS,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。