- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181BDGG (NXP SEMICONDUCTORS) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181BDGG |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PDSO48 |
| 封裝： | 6.10 MM, PLASTIC, MO-153, SOT-362-1, TSSOP-48 |
| 文件頁數： | 10/70頁 |
| 文件大小： | 341K |
| 代理商： | ISP1181BDGG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
10 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
V
BUS
sensing prevents the peripheral from wake-up when V
BUS
is not present.
Without V
BUS
sensing, any activity or noise on (D+, D-) might wake up the peripheral.
With V
BUS
sensing, (D+, D-) is decoupled when no V
BUS
is present. Therefore, even if
there is noise on the (D+, D-) lines, it is not taken into account. This ensures that the
peripheral remains in the suspend state.
Remark:
Note that the tolerance of the internal resistors is 25 %. This is higher than
the 5 % tolerance specified by the USB specification. However, the overall voltage
specification for the connection can still be met with a good margin. The decision to
make use of this feature lies with the USB equipment designer.
7.5 GoodLink
Indication of a good USB connection is provided at pin GL through GoodLink
technology. During enumeration, the LED indicator will blink on momentarily. When
the ISP1181B has been successfully enumerated (the peripheral address is set), the
LED indicator will remain permanently on. Upon each successful packet transfer (with
ACK) to and from the ISP1181B, the LED will blink off for 100 ms. During ‘suspend’
state, the LED will remain off.
This feature provides a user-friendly indication of the status of the USB peripheral,
the connected hub, and the USB traffic. It is a useful field diagnostics tool for isolating
faulty equipment. It can therefore help to reduce field support and hotline overhead.
7.6 Bit clock recovery
The bit clock recovery circuit recovers the clock from the incoming USB data stream
using a 4 times over-sampling principle. It is able to track jitter and frequency drift as
specified by the USB Specification Rev. 2.0
7.7 Voltage regulator
A 5 V-to-3.3 V voltage regulator is integrated on-chip to supply the analog transceiver
and internal logic. This voltage is available at pin V
reg(3.3)
to supply an external 1.5 k
pull-up resistor on the D
+
line. Alternatively, the ISP1181B provides SoftConnect
technology via an integrated 1.5 k
pull-up resistor (see
Section 7.4
).
7.8 PLL clock multiplier
A 6 MHz to 48 MHz clock multiplier Phase-Locked Loop (PLL) is integrated on-chip.
This allows for the use of a low-cost 6 MHz crystal, which also minimizes EMI. No
external components are required for the operation of the PLL.
7.9 Parallel I/O (PIO) and Direct Memory Access (DMA) interface
A generic PIO interface is defined for speed and ease-of-use. It also allows direct
interfacing to most microcontrollers. To a microcontroller, the ISP1181B appears as a
memory device with an 8/16-bit data bus and a 1-bit address line. The ISP1181B
supports both multiplexed and non-multiplexed address and data buses.
The ISP1181B can also be configured as a DMA slave device to allow more efficient
data transfer. One of the 14 endpoint FIFOs may directly transfer data to/from the
local shared memory. The DMA interface can be configured independently from the
PIO interface.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
| ISP1183BS | Low-power Universal Serial Bus interface device with DMA |
| ISP1301 | Universal Serial Bus On-The-Go transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181BDGG,112 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BDGG,118 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BDGG-T | 制造商:ST-Ericsson 功能描述:USB Peripheral Controller 48-Pin TSSOP T/R |
| ISP1181BDGGTM | 功能描述:IC USB HOST CTRL FLL-SPD 48TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ISP1181BPC | 制造商:ST-Ericsson 功能描述:Full-Speed Universal Serial Bus Peripheral Controller |
發布緊急采購，3分鐘左右您將得到回復。