- 您現在的位置：買賣IC網 > PDF目錄30737 > LC89052TA-E SPECIALTY CONSUMER CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | LC89052TA-E |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| 封裝： | 0.225 INCH, TSSOP-24 |
| 文件頁數： | 17/42頁 |
| 文件大小： | 224K |
| 代理商： | LC89052TA-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LC89052TA-E
No.7457-24/42
8.7 User General Definable Output Port (
__________
UGPI )
__________
UGPI pin is a user-definable output port that can be selected for the following functions.
—Microcontroller interface register output
—Signal output during clock switching transitional period
Selection is done by GPISEL. The initial setting is set to the microcontroller interface register GPIDAT. However, the
initial setting of this GPIDAT register is "1", so high level is output from the
__________
UGPI pin.
8.7.1 Microcontroller interface register output (Example of signals that control low power of optical module)
This section describes an example in which
__________
UGPI is used as a power supply control signal for an optical module as a
microcontroller interface register output.
(a) Connect the
__________
UGPI output to the power supply control switch of the optical module.
(b) After a reset due to
_____
PD, microcontroller interface register output is selected as the initial state of
__________
UGPI. As a result,
the default GPIDAT value is output.
(c) After a reset, the initial value of GPIDAT is set to "1", so H is output from
__________
UGPI. Therefore, after a reset, the
control switch is turned off, and data is not supplied from the optical module.
(d) The application must set GPIDAT to "0" to have the optical module supply data. That is, the
__________
UGPI output can be
controlled with GPIDAT, and the current drain can be minimized when the optical module is not used.
Figure 8.12
__________
UGPI Output Example (Power supply control signal for an optical module)
LC89052TA-E
UGPI
RXIN
Optical receiver
module
相關PDF資料 |
PDF描述 |
|---|---|
| LC890561W | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC890561W | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89057W-VF4-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89057W-VF4A-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC89057W-VF4 | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC89052TA-TLM-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89052THS-E | 制造商:ON Semiconductor 功能描述:AUDIO I/F RECEIVER |
| LC890561W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Digital Audio Interface Receiver with Built-in Data Buffer Memory |
| LC890561W-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| LC89056W-E | 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
發布緊急采購，3分鐘左右您將得到回復。