欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: LC89052TA-E
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PDSO24
封裝: 0.225 INCH, TSSOP-24
文件頁數: 7/42頁
文件大小: 224K
代理商: LC89052TA-E
LC89052TA-E
No.7457-15/42
8.3.4 Clock system diagram
This section shows the relationship between the two types of master clock and clock switching and dividing functions.
The items in square brackets near the switch and function blocks are the names of write commands.
Lock/Unlock is switched automatically according to the PLL lock/unlock state.
Figure 8.5 Master Clock System Diagram
8.3.5 Point to notice when switching the clock source
If an attempt is made to switch the clock source from PLL lock state (oscillator amplifier stopped) to XIN using
OCKSEL when a mode in which the results of input fs calculation are reflected in the error flags is specified through
FLIMIT, an error signal (H) is temporarily placed at the ERROR pin though the continuity of the clock is preserved.
The reason for this follows. When the clock switching is carried out, the oscillator amplifier is activated and the input
fs calculation is restarted. At the same time, the old results of fs calculation are reset and consequently, a change in
the fs value is recognized when the old fs value is compared with the newly calculated fs value.
To switch the clock source using OCKSEL while maintaining the state of the ERROR pin when the PLL is locked in
this mode setting, it is necessary to put the oscillator amplifier into the continuous mode using AMPCNT.
Note that when the clock source is switched to XIN from the state where the oscillator amplifier is stopped with the
PLL circuit locked, output clocks whose source is XIN start outputting after the oscillator amplifier has started
operation. While the PLL is locked, clock source switching from XIN to PLL is carried out immediately. In both
cases, clock continuity is maintained.
When the CKOUT clock is supplied to XIN without using an oscillator or an external clock, the VCO free-running
frequency output from the CKOUT pin with the PLL unlocked is somewhere between 10M and 16MHz. Clock
signals created by dividing CKOUT are output from BCK and LRCK pins. However, these clock frequencies vary
depending on the LC89052TA-E sample and fluctuate depending on supply voltage and operating environments.
Therefore, the frequency is not fixed. You need to take care when using the CKOUT, BCK, and LRCK clocks while
the PLL circuit is unlocked.
RXIN
Lock/Unlock
[OCKSEL]
Divider
1/2
Divider
1/256
CKOUT
BCK
LRCK
XIN
XOUT
PLL
(256fs)
[PLLCK0]
[XISEL0]
(384fs)
[PLLOPR]
[AMPCNT]
1/3
1/384
[XINSET]
[AMPOPR]
[XISEL1]
[PLLCK1]
[XISEL2]
(512fs)
1/512
(512/2fs)
Divider
1/2
[MCKHFO]
1/4
1/6
1/8
相關PDF資料
PDF描述
LC890561W SPECIALTY CONSUMER CIRCUIT, PQFP48
LC890561W SPECIALTY CONSUMER CIRCUIT, PQFP48
LC89057W-VF4-E SPECIALTY CONSUMER CIRCUIT, PQFP48
LC89057W-VF4A-E SPECIALTY CONSUMER CIRCUIT, PQFP48
LC89057W-VF4 SPECIALTY CONSUMER CIRCUIT, PQFP48
相關代理商/技術參數
參數描述
LC89052TA-TLM-E 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
LC89052THS-E 制造商:ON Semiconductor 功能描述:AUDIO I/F RECEIVER
LC890561W 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Digital Audio Interface Receiver with Built-in Data Buffer Memory
LC890561W-E 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
LC89056W-E 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
主站蜘蛛池模板: 泰州市| 布尔津县| 紫金县| 万荣县| 华宁县| 金华市| 神农架林区| 武陟县| 湘阴县| 鄂托克前旗| 盘山县| 和平区| 仁寿县| 商都县| 万盛区| 博野县| 白水县| 南皮县| 武城县| 德庆县| 广灵县| 柯坪县| 长武县| 洪泽县| 涞源县| 上蔡县| 明溪县| 潢川县| 武夷山市| 攀枝花市| 南京市| 江安县| 武汉市| 胶南市| 凯里市| 炎陵县| 大余县| 霞浦县| 通州市| 涿州市| 锡林郭勒盟|