欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: LFEC6E-3F256C
廠商: Lattice Semiconductor Corporation
文件頁數: 129/163頁
文件大小: 0K
描述: IC FPGA 6.1KLUTS 195I/O 256-BGA
標準包裝: 90
系列: EC
邏輯元件/單元數: 6100
RAM 位總計: 94208
輸入/輸出數: 195
電源電壓: 1.14 V ~ 1.26 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 256-BGA
供應商設備封裝: 256-FPBGA(17x17)
其它名稱: 220-1236
4-2
Pinout Information
LatticeECP/EC Family Data Sheet
TDI
I
Test Data in pin. Used to load data into device using 1149.1 state machine.
After power-up, this TAP port can be activated for configuration by sending
appropriate command. (Note: once a configuration port is selected it is
locked. Another configuration port cannot be selected until the power-up
sequence). Pull-up is enabled during configuration.
TDO
O
Output pin. Test Data out pin used to shift data out of device using 1149.1.
VCCJ
—VCCJ - The power supply pin for JTAG Test Access Port.
Configuration Pads (used during sysCONFIG)
CFG[2:0]
I
Mode pins used to specify configuration modes values latched on rising edge
of INITN. During configuration, a pull-up is enabled. These are dedicated
pins.
INITN
I/O
Open Drain pin. Indicates the FPGA is ready to be configured. During config-
uration, a pull-up is enabled. It is a dedicated pin.
PROGRAMN
I
Initiates configuration sequence when asserted low. This pin always has an
active pull-up. This is a dedicated pin.
DONE
I/O
Open Drain pin. Indicates that the configuration sequence is complete, and
the startup sequence is in progress. This is a dedicated pin.
CCLK
I/O
Configuration Clock for configuring an FPGA in sysCONFIG mode.
BUSY/SISPI
I/O
Read control command in SPI3 or SPIX mode.
CSN
I
sysCONFIG chip select (Active low). During configuration, a pull-up is
enabled.
CS1N
I
sysCONFIG chip select (Active low). During configuration, a pull-up is
enabled.
WRITEN
I
Write Data on Parallel port (Active low).
D[7:0]/SPID[0:7]
I/O
sysCONFIG Port Data I/O.
DOUT/CSON
O
Output for serial configuration data (rising edge of CCLK) when using sys-
CONFIG port.
DI/CSSPIN
I/O
Input for serial configuration data (clocked with CCLK) when using sysCON-
FIG port. During configuration, a pull-up is enabled. Output when used in
SPI/SPIX modes.
Signal Descriptions (Cont.)
Signal Name
I/O
Description
相關PDF資料
PDF描述
VE-25R-CW-F3 CONVERTER MOD DC/DC 7.5V 100W
REC3-1212DRW/H2/A CONV DC/DC 3W 9-18VIN +/-12VOUT
LFXP10C-3FN388C IC FPGA 9.7KLUTS 244I/O 388-BGA
FAN5345S20X IC LED DVR ASYNC BOOST 20V 6SSOT
VI-B21-CY-S CONVERTER MOD DC/DC 12V 50W
相關代理商/技術參數
參數描述
LFEC6E-3F256I 功能描述:FPGA - 現場可編程門陣列 6.1 LUT 195 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
LFEC6E-3F484C 功能描述:FPGA - 現場可編程門陣列 6.1 LUT 224 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
LFEC6E-3F484I 功能描述:FPGA - 現場可編程門陣列 6.1 LUT 224 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
LFEC6E-3F672C 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC6E-3F672I 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
主站蜘蛛池模板: 休宁县| 尤溪县| 丰原市| 连平县| 南溪县| 连江县| 汾西县| 大石桥市| 徐州市| 德令哈市| 阳谷县| 宁强县| 金乡县| 灵川县| 梧州市| 汝南县| 正定县| 承德市| 瓦房店市| 涟源市| 建宁县| 黔西| 苗栗县| 淮南市| 泸水县| 桐柏县| 墨玉县| 托里县| 洛阳市| 万载县| 游戏| 凭祥市| 夏津县| 中阳县| 岐山县| 石门县| 徐州市| 陆川县| 于都县| 什邡市| 醴陵市|