
DAC Output Electrical Characteristics
Unless otherwise noted: T
A = 25°C, VCC = +5.0V, VIN = 0.7V, VABL = VCC, CL = 8 pF, Video Outputs = 2.0 VP-P. See (Note 7) for Min and Max parameters and
(Note 6) for Typicals. DAC parameters apply to all 4 DACs.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
Min DAC
Min Output Voltage of DAC
Register Value = 0x00
0.5
0.7
V
Max DAC
Mode 00
Max Output Voltage of DAC
Register Value = 0xFF,
DCF[1:0] = 00b
3.7
4.2
V
Max DAC
Mode 01
Max Output Voltage of DAC in DCF
Mode 01
Register Value = 0xFF,
DCF[1:0] = 01b
1.85
2.35
V
ΔV
Max DAC (Temp)
DAC Output Voltage Variation with
Temperature
0 < T < 70°C ambient
±0.5
mV/°C
ΔV
Max DAC (VCC)
DAC Output Voltage Variation with
V
CC
V
CC varied from 4.75V to 5.25V, DAC
register set to mid-range (0x7F)
50
mV
Linearity
Linearity of DAC over its Range
5
%
Monotonicity
Monotonicity of the DAC Excluding
Dead Zones
±0.5
LSB
I
MAX
Max Load Current
1.0
mA
System Interface Signal Characteristics
Unless otherwise noted: T
A = 25°C, VCC = +5.0V, VIN = 0.7V, VABL = VCC, CL = 8 pF, Video Outputs = 2.0 VP-P. See (Note 7) for Min and Max parameters and
(Note 6) for Typicals. DAC parameters apply to all 4 DACs.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
VTH+
VFLYBACK Positive Switching
Guarantee
Vertical Blanking triggered
2.0
V
SPOT
Spot Killer Voltage
CC Adjusted to Activate
3.4
3.9
4.3
V
Ref
V
Ref Output Voltage (pin 2)
1.25
1.45
1.65
V
IL (SCL, SDA)
Logic Low Input Voltage
0.5
1.5
V
IH (SCL, SDA)
Logic High Input Voltage
3.0
V
CC + 0.5
V
I
L (SCL, SDA)
Logic Low Input Current
SDA or SCL, Input Voltage = 0.4V
±10
A
I
H (SCL, SDA)
Logic High Input Voltage
SDA or SCL, Input Voltage = 4.5V
±10
A
V
OL (SCL, SDA)
Logic Low Output Voltage
I
O = 3 mA
0.5
V
f
H Min
Minimum Horizontal Frequency
PLL & OSD Functioning
25
kHz
f
H Max
Maximum Horizontal Frequency
PLL & OSD Functioning
110
kHz
I
HFB IN Max
Horizontal Flyback Input
Current Absolute Maximum during
Flyback
5
mA
I
IN
Peak Current during Flyback
Design Value
4
mA
I
HFB OUT Max
Horizontal Flyback Input Current
Absolute Maximum during Scan
700
A
I
OUT
Peak Current during Scan
Not exact - Duty Cycle Dependent
550
A
I
IN THRESHOLD
I
IN H-Blank Detection Threshold
0
A
t
H-BLANK ON
H-Blank Time Delay - On
+ Zero crossing of I
HFB to 50% of output
blanking start. I
24 = +1.5mA
45
ns
t
H-BLANK OFF
H-Blank Time Delay - Off
Zero crossing of I
HFB to 50% of output
blanking end. I
24 = 100A
85
ns
V
BLANK Max
Maximum Video Blanking Level
Test Setting 4, AC input signal
0
0.25
V
f
FREERUN
Free Run H Frequency, Including H
Blank
42
kHz
t
PW CLAMP
Minimum Clamp Pulse Width
200
ns
V
CLAMP MAX
Maximum Low Level Clamp Pulse
Voltage
Video Clamp Functioning
2.0
V
CLAMP MIN
Minimum High Level Clamp Pulse
Voltage
Video Clamp Functioning
3.0
V
www.national.com
6
200969 Version 2 Revision 4
Print Date/Time: 2011/07/11 11:20:12
LM1276