- 您現在的位置：買賣IC網 > PDF目錄361030 > LM5642 (National Semiconductor Corporation) High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization PDF資料下載
參數資料
| 型號： | LM5642 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization |
| 中文描述： | 高電壓，雙同步降壓轉換器振蕩器同步 |
| 文件頁數： | 21/24頁 |
| 文件大小： | 667K |
| 代理商： | LM5642 |
Loop Compensation
(Continued)
As shown in
Figure 11
, the control-output transfer function
consists of one pole (fp), one zero (fz), and a double pole at
fn (half the switching frequency). The following can be done
to create a -20dB /decade roll-off of the loop gain: Place the
first pole at 0Hz, the first zero at fp, the second pole at fz,
and the second zero at fn. The resulting output-control trans-
fer function is shown in
Figure 12
.
The control-output corner frequencies, and thus the desired
compensation corner frequencies, can be determined ap-
proximately by the following equations:
(29)
(30)
Since fp is determined by the output network, it will shift with
loading (Ro). It is best to use a minimum Iout value of
approximately 100mA when determining the maximum Ro
value.
Example: Re=20m
, Co=100uF, Romax=5V/100mA=50
:
(31)
(32)
First determine the minimum frequency (fpmin) of the pole
across the expected load range, then place the first compen-
sation zero at or below that value. Once fpmin is determined,
Rc1 should be calculated using:
(33)
Where B is the desired gain in V/V at fp (fz1), gm is the
transconductance of the error amplifier, and R1 and R2 are
the feedback resistors. A gain value around 10dB (3.3v/v) is
generally a good starting point.
Example: B=3.3v/v, gm=650m, R1=20K
, R2=60.4K
:
(34)
Bandwidth will vary proportional to the value of Rc1. Next,
Cc1 can be determined with the following equation:
(35)
Example: fpmin=695Hz, Rc1=20K
:
(36)
The compensation network (
Figure 13
) will also introduce a
low frequency pole which will be close to 0Hz.
A second pole should also be placed at fz. This pole can be
created with a single capacitor Cc2 and a shorted Rc2 (see
Figure 13
). The minimum value for this capacitor can be
calculated by:
(37)
Cc2 may not be necessary, however it does create a more
stable control loop. This is especially important with high
load currents and in current sharing mode.
Example: fz=80kHz, Rc1= 20K
:
(38)
A second zero can also be added with a resistor in series
with Cc2. If used, this zero should be placed at fn, where the
control to output gain rolls off at -40dB/dec. Generally, fn will
be well below the 0dB level and thus will have little effect on
stability. Rc2 can be calculated with the following equation:
(39)
20060114
FIGURE 11. Control-Output Transfer Function
20060112
FIGURE 12. Output-Control Transfer Function
L
www.national.com
21
相關PDF資料 |
PDF描述 |
|---|---|
| LM5642MTC | High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization |
| LM565 | Phase Locked Loop |
| LM565C | |
| LM565CH | Analog Phase-Locked Loop |
| LM565CN | Phase Locked Loop |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5642_07 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization |
| LM5642EVAL-KIT | 功能描述:BOARD EVALUATION LM5642 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM5642EVAL-KIT/NOPB | 功能描述:電源管理IC開發工具 LM5642 EVAL KIT RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM5642MH | 制造商:Texas Instruments 功能描述: |
| LM5642MH/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。