- 您現在的位置：買賣IC網 > PDF目錄361044 > LMX9820A (National Semiconductor Corporation) Bluetooth Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9820A |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Bluetooth Serial Port Module |
| 中文描述： | 藍牙串行端口模塊 |
| 文件頁數： | 24/44頁 |
| 文件大小： | 579K |
| 代理商： | LMX9820A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
www.national.com
24
Revision 1.0
L
10.0 Integrated Firmware
(Continued)
10.0 Integrated Firmware
The LMX9820A includes the full Bluetooth protocol stack
up to RFComm to support the following profiles:
— GAP (Generic Access Profile)
— SDAP (Service Discovery Application Profile)
— SPP (Serial Port Profile)
Figure 16 shows the Bluetooth protocol stack with com-
mand interpreter interface. The command interpreter offers
a number of different commands to support the functional-
ity given by the different profiles. Execution and interface
timing is handled by the control application.
The chip has an internal data area in Flash that includes
the parameters shown in Table 26 on page 25.
10.1 FEATURES
10.1.1 Operation Modes
On boot-up, the application configures the module follow-
ing the parameters in the data area.
Automatic Mode
No Default Connections Stored
In Automatic mode the module is connectable and discov-
erable and automatically answers to service requests. The
command interpreter listens to commands and links can be
set up. The full command list is supported.
If connected by another device, the module sends an event
back to the host, where the RFComm port has been con-
nected, and switches to transparent mode.
Default Connections Stored
If default connections were stored on a previous session,
after the LMX9820A is reset, it will attempt to reconnect to
each device stored within the data Flash three times. The
host will be notified about the success of the link setup via
a link status event.
Command Mode
In Command mode, the LMX9820A does not check the
default connections section within the Data Flash. If con-
nected by another device, it will
not
switch to transparent
mode and continue to interpret data sent on the UART.
Transparent Mode
The LMX9820A supports transparent data communication
from the UART interface to a Bluetooth link.
If activated, the module does not interpret the commands
on the UART which normally are used to configure and
control the module. In this case, the packets do not need to
be formatted as described in Table 28 on page 27. Instead,
all data are directly passed through the firmware to the
active Bluetooth link and the remote device.
Transparent mode can only be supported on a point-to-
point connection. To leave Transparent mode, the host
must send a UART_BREAK signal to the module
Force Master Mode
In Force Master mode, the LMX9820A tries to act like an
Access point for multiple connections. In this mode, it will
only accept a link if a master/slave role switch is accepted
by the connecting device. After successful link establish-
ment, the LMX9820A will be master and available for addi-
tional incoming links. On the first incoming link the
LMX9820A may switch to transparent mode, depending on
the setting for automatic or command mode. Additional
links will only be possible if the device is not in transparent
mode.
10.1.2 Default Connections
The LMX9820A supports the storage of up to 3 default con-
nections within its NVS. Those connections can either be
connected after reset or on demand using a specific com-
mand.
10.1.3 Event Filter
The LMX9820A uses events or indicators to notify the host
about successful commands or changes on the Bluetooth
interface. Depending on the application, the LMX9820A
can be configured. The following levels are defined:
No Events
—the LMX9820A is not reporting any events.
Optimized for passive cable replacement solutions.
Standard LMX9820A Events
—only necessary events
will be reported.
All Events
—additional to the standard all changes at the
physical layer will be reported.
10.1.4 Default Link Policy
Each Bluetooth link can be configured to support mas-
ter/slave role switch, Hold mode, Sniff mode, and Park
mode. The default link policy defines the standard setting
for incoming and outgoing connections.
10.1.5 Audio Support
The LMX9820A offers commands to establish and release
synchronous connections (SCO) to support Headset or
Handsfree applications. The firmware supports one active
link with all available package types (HV1, HV2, HV3), for
routing audio data between the Bluetooth link and the
advanced audio interface. To provide the analog data inter-
face, an external audio codec is required. The LMX9820A
includes a list of codecs which can be used.
Figure 16. LMX9820A Software Implementation
Command Interpreter
Control Application
SPP
GAP
SDAP
RFComm
L2CAP
Link Manager
Baseband
SDP
相關PDF資料 |
PDF描述 |
|---|---|
| LMX9820ASM | Bluetooth Serial Port Module |
| LMX9820 | Bluetooth Serial Port Module |
| LMX9820SB | Bluetooth Serial Port Module |
| LMX9820SBX | Bluetooth Serial Port Module |
| LP3882ESX-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9820ADEV | 制造商:Texas Instruments 功能描述:KIT DEV FOR LMX9820 |
| LMX9820ADONGLE/NOPB | 制造商:Texas Instruments 功能描述:KIT REF DESIGN FOR LMX9820 |
| LMX9820ASM | 制造商:Texas Instruments 功能描述:BLUETOOTH MODULE, SMD, 9820, FR4129 |
| LMX9820ASM/NOPB | 制造商:Texas Instruments 功能描述:IC MODULE BLUETOOTH 116-LTCC |
| LMX9820ASMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth Serial Port Module |
發布緊急采購，3分鐘左右您將得到回復。