- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5952CUAX+ (Maxim Integrated)IC PSE CNTRLR FOR POE 36-SSOP Datasheet資料下載
參數資料
| 型號： | MAX5952CUAX+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 24/50頁 |
| 文件大小： | 1006K |
| 描述： | IC PSE CNTRLR FOR POE 36-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 30 |
| 類型： | 以太網供電控制器（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 無 |
| 工作溫度： | 0°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-BSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
24 ______________________________________________________________________________________
Figure 9. Slave Address
SDA
SCL
1
0
A3
A2
A1
A0
0
MSB
LSB
ACK
R/W
Figure 10. Control Byte Received
S
A
A
P
0
SLAVE ADDRESS
CONTROL BYTE
ACKNOWLEDGE FROM MAX5952
ACKNOWLEDGE FROM MAX5952
D15 D14 D13 D12 D11 D10 D9 D8
CONTROL BYTE IS STORED ON RECEIPT OF STOP CONDITION
R/W
Slave Address
The MAX5952 has a 7-bit long slave address (Figure
9). The bit following the 7-bit slave address (bit eight) is
the R/W bit, which is low for a write command and high
for a read command.
010 always represents the first three bits (MSBs) of the
MAX5952 slave address. Slave address bits A3, A2,
A1, and A0 represent the states of the MAX5952s A3,
A2, A1, and A0 inputs, allowing up to sixteen MAX5952
devices to share the bus. The states of the A3, A2, A1
and A0 latch in upon the reset of the MAX5952 into reg-
ister R11h. The MAX5952 monitors the bus continuous-
ly, waiting for a START condition followed by the
MAX5952s slave address. When a MAX5952 recog-
nizes its slave address, the MAX5952 acknowledges
and is then ready for continued communication.
Global Addressing and Alert Response Protocol
The global address call is used in writing mode to write
the same register to multiple devices (address 0x60). In
read mode (address 0x61), the global address call is
used as the alert response address. When responding
to a global call, the MAX5952 puts out on the data line
its own address whenever its interrupt is active. So
does every other device connected to the SDAOUT line
that has an active interrupt. After every bit transmitted,
the MAX5952 checks that the data line effectively cor-
responds to the data it is delivering. If it is not, it then
backs off and frees the data line. This litigation protocol
always allows the part with the lowest address to com-
plete the transmission. The microcontroller can then
respond to the interrupt and take proper actions. The
MAX5952 does not reset its own interrupt at the end of
the alert response protocol. The microcontroller has to
do it by clearing the event register through their CoR
adresses or activating the CLR_INT pushbutton.
Message Format for Writing to the MAX5952
A write to the MAX5952 comprises of the MAX5952s
slave address transmission with the R/W bit set to 0, fol-
lowed by at least one byte of information. The first byte
of information is the command byte (Figure 10). The
command byte determines which register of the
MAX5952 is written to by the next byte, if received. If
the MAX5952 detects a STOP condition after receiving
the command byte, the MAX5952 takes no further
action beyond storing the command byte. Any bytes
received after the command byte are data bytes. The
first data byte goes into the internal register of the
MAX5952 selected by the command byte. If the
MAX5952 transmits multiple data bytes before the
MAX5952 detects a STOP condition, these bytes store
in subsequent MAX5952 internal registers because the
control byte address auto-increments.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5953DUTM+ | IC INTERFACE 802.3AF 48TQFN |
| MAX5954LETX+T | IC PCI EXP/HOT-PLUG CTRLR 36TQFN |
| MAX5955BEEE+ | IC DUAL HOT-SWAP CTRLR 16-QSOP |
| MAX5957AETN+T | IC TRPL PCI EXP/HOT-PLUG 56-TQFN |
| MAX5960AECS+T | IC CTRLR HOT-PLUG QD 80-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5952CUAX+ | 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5952CUAX+T | 功能描述:熱插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5952DEAX+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5952DEAX+T | 制造商:Maxim Integrated Products 功能描述:HIGH-POWER QUAD PSE CONTROLLER FOR - Tape and Reel |
| MAX5952DUAX+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。