欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MBM29PL12LM10PBT
廠商: Fujitsu Limited
英文描述: FLASH MEMORY 128 M (16M ?8/8M ?16) BIT
中文描述: 快閃記憶體128米(1,600?8/8M?16)位
文件頁數: 31/72頁
文件大小: 1036K
代理商: MBM29PL12LM10PBT
MBM29PL12LM
10
31
Erase Suspend/Resume
The Erase Suspend command allows the user to interrupt Sector Erase operation and then perform read to a
sector not being erased. This command is applicable ONLY during the Sector Erase operation within the time-
out period for sector erase. Writting the Erase Suspend command (B0h) during the Sector Erase time-out results
in immediate termination of the time-out period and suspension of the erase operation.
Writing the "Erase Resume" command resumes the erase operation.
When the "Erase Suspend" command is written during the Sector Erase operation, the device takes maximum
of “t
SPD
” to suspend the erase operation. When the devices enter the erase-suspended mode, the RY/BY output
pin will be at High-Z and the DQ
7
bit will be at logic “1” and DQ
6
will stop toggling. The user must use the address
of the erasing sector for reading DQ
6
and DQ
7
to determine if the erase operation has been suspended. Further
writes of the Erase Suspend command are ignored.
When the erase operation is suspended, the devices default to the erase-suspend-read mode. Reading data in
this mode is the same as reading from the standard read mode, except that the data must be read from sectors
that have not been erase-suspended. Reading successively from the erase-suspended sector while the device
is in the erase-suspend-read mode will cause DQ
2
to toggle. See the section on DQ
2
.
To resume the operation of Sector Erase, the Resume command (30h) should be written. Any further writes of
the Resume command at this point will be ignored. Another Erase Suspend command can be written after the
chip has resumed erasing.
Do not issue program command after entering erase-suspend-read mode.
Fast Mode Set/Reset
The device has Fast Mode function. It dispenses with the initial two unclock cycles required in the standard
program command sequence by writing Fast Mode command into the command register. In this mode, the
required bus cycle for programming consists of two cycles instead of 4 bus cycles in standard program command.
The read operation is also executed after exiting this mode. During the Fast mode, do not write any command
other than the Fast program/Fast mode reset command. To exit from this mode, write Fast Mode Reset command
into the command register. (Refer to the “Embedded Program
TM
Algorithm for Fast Mode” in
FLOW CHART.)
The V
CC
active current is required even CE = V
IH
during Fast Mode.
Fast Programming
During Fast Mode, the programming can be executed with 2 bus cycles operation. The Embedded Program
Algorithm is executed by writing program set-up command (A0h) and data write cycles (PA/PD). See “Embedded
Program
TM
Algorithm for Fast Mode” in
FLOW CHART.
相關PDF資料
PDF描述
MBM29PL12LM10PCN FLASH MEMORY 128 M (16M ?8/8M ?16) BIT
MBM30LV0064-PFTN 64M (8M X 8) BIT NAND-type
MBM30LV0064-PFTR 64M (8M X 8) BIT NAND-type
MBM30LV0032 32M (4M X 8) BIT NAND-type
MBM30LV0032-PFTN 32M (4M X 8) BIT NAND-type
相關代理商/技術參數
參數描述
MBM30000 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制,儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183
MBM30035001 制造商:LG Corporation 功能描述:Card,Technical
MBM30035015 制造商:LG Corporation 功能描述:Card,Technical
MBM300A6 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
MBM300GR12A 制造商:n/a 功能描述:IGBT Module
主站蜘蛛池模板: 蚌埠市| 沈阳市| 青川县| 盘山县| 陕西省| 岱山县| 杨浦区| 南昌市| 友谊县| 灌云县| 思茅市| 肥城市| 顺平县| 石门县| 海伦市| 临澧县| 公主岭市| 名山县| 密山市| 泉州市| 民丰县| 大余县| 宣恩县| 甘德县| 门头沟区| 南城县| 吉安市| 通榆县| 周口市| 黄龙县| 吉木萨尔县| 曲沃县| 扎兰屯市| 罗源县| 孙吴县| 黄龙县| 沈丘县| 乌兰察布市| 拜泉县| 福贡县| 蚌埠市|