- 您現在的位置：買賣IC網 > PDF目錄371047 > MC68HC05BD3 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | MC68HC05BD3 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 35/112頁 |
| 文件大小： | 676K |
| 代理商： | MC68HC05BD3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
MC68HC05BD3
MOTOROLA
4-3
RESETS AND INTERRUPTS
4
Note:
COP time-out is prevented by periodically writing a “0” to bit 0 of address $3FF0.
If the watchdog timer is allowed to time-out, an internal reset is generated to reset the MCU.
Because the internal reset signal is used, the MCU comes out of a COP reset in the same
operating mode it was in when the COP time-out was generated.
The COP reset function is always enabled.
See Section 5.3 for more information on the COP watchdog timer.
4.2
INTERRUPTS
The MCU can be interrupted by different sources – four maskable hardware interrupt and one
non-maskable software interrupt:
External signal on the IRQ pin
Multi-Function Timer (MFT)
M-Bus Interface (MBUS)
Sync Signal Processor (SSP)
Software Interrupt Instruction (SWI)
If the interrupt mask bit (I-bit) of the CCR is set, all maskable interrupts (internal and external) are
disabled. Clearing the I-bit enables interrupts.
Interrupts cause the processor to save the register contents on the stack and to set the interrupt
mask (I-bit) to prevent additional interrupts. The RTI instruction causes the register contents to be
recovered from the stack and normal processing to resume.
Unlike reset, hardware interrupts do not cause the current instruction execution to be halted, but
are considered pending until the current instruction is complete. The current instruction is the one
already fetched and being operated on. When the current instruction is complete, the processor
checks all pending hardware interrupts. If interrupts are not masked (CCR I-bit clear) the
processor proceeds with interrupt processing; otherwise, the next instruction is fetched and
executed.
Table 4-1 shows the relative priority of all the possible interrupt sources.
4.2.1
Non-maskable Software Interrupt (SWI)
The software interrupt (SWI) is an executable instruction and a non-maskable interrupt: it is
execute regardless of the state of the I-bit in the CCR. If the I-bit is zero (interrupt enabled), SWI
is executed after interrupts that were pending when the SWI was fetched, but before interrupts
generated after the SWI was fetched. The SWI interrupt service routine address is specified by
the contents of memory locations $3FFC and $3FFD.
TPG
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05BD5 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HC705BD3 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HC05C4 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HC05C5 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HC05C8A | Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05BD5 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit |
| MC68HC05C0CP | 制造商:Motorola Inc 功能描述: |
| MC68HC05C12 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS |
| MC68HC05C12B | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS |
| MC68HC05C12CP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS |
發布緊急采購，3分鐘左右您將得到回復。