欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HC05BD3
廠商: Motorola, Inc.
英文描述: 8-Bit Microcontroller Units (MCU).(8位微控制器)
中文描述: 8位微控制器單元(MCU)。(8位微控制器)
文件頁數: 50/112頁
文件大小: 676K
代理商: MC68HC05BD3
MOTOROLA
7-4
MC68HC05BD3
M-BUS SERIAL INTERFACE
7
7.2.3
Data Transfer
Once a successful slave addressing is achieved, the data transfer can proceed byte by byte in a
direction specified by the R/W bit sent by the calling master.
Each data byte is 8 bits long. Data can be changed only when SCL is low and must be held stable
when SCL is high as shown in Figure 7-2. One clock pulse is for one bit of data transfer, MSB is
transferred first. Each data byte has to be followed by an acknowledge bit. Hence, one complete
data byte transfer requires 9 clock pulses.
If the slave receiver does not acknowledge the master, the SDA line should be left high by the
slave, the master can then generate a STOP signal to abort the data transfer or a START signal
(repeated START) to commence a new calling.
If the master receiver does not acknowledge the slave transmitter after one byte transmission, it
means an “end of data” to the slave. The slave shall release the SDA line for the master to
generate STOP or START signal.
7.2.4
Repeated START Signal
As shown in Figure 7-2, a repeated START signal is to generate a START signal without first
generating a STOP signal to terminate the communication. This is used by the master to
communicate with another slave or with the same slave in a different mode (transmit/receive
mode) without releasing the bus.
7.2.5
STOP Signal
The master can terminate the communication by generating a STOP signal to free the bus.
However, the master may generate a START signal followed by a calling command without
generating a STOP signal first. This is called repeat START. A STOP signal is defined as a low to
high transition of SDA while SCL is at a logical high; see Figure 7-2.
7.2.6
Arbitration Procedure
This interface circuit is a true multi-master system which allows more than one master to be
connected. If two or more masters try to control the bus at the same time, a clock synchronization
procedure determines the bus clock. The clock low period is equal to the longest clock low period
among the masters; and the clock high period is the shortest among the masters. A data
arbitration procedure determines the priority. A master will lose arbitration if it transmits a logic “1”
while the others transmit logic “0”, the losing master will immediately switch over to slave receive
mode and stops its data and clock outputs. The transition from master to slave mode will not
generate a STOP condition. Meanwhile, a software bit will be set by hardware to indicate loss of
arbitration.
TPG
相關PDF資料
PDF描述
MC68HC05BD5 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC705BD3 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C4 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C5 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HC05C8A Microcontrollers
相關代理商/技術參數
參數描述
MC68HC05BD5 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit
MC68HC05C0CP 制造商:Motorola Inc 功能描述:
MC68HC05C12 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
MC68HC05C12B 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
MC68HC05C12CP 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS
主站蜘蛛池模板: 三明市| 杂多县| 黄浦区| 庆安县| 龙陵县| 黔西县| 黄梅县| 东海县| 通州区| 定结县| 外汇| 边坝县| 普安县| 扎赉特旗| 凤山市| 永靖县| 无棣县| 若尔盖县| 凤翔县| 呼伦贝尔市| 南汇区| 金寨县| 古浪县| 阳山县| 蓬安县| 兴安盟| 科技| 和硕县| 镇赉县| 长沙县| 当涂县| 南汇区| 卢湾区| 红安县| 五寨县| 灵台县| 玉龙| 兖州市| 金华市| 兴宁市| 通海县|