- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HC11A1CFN2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HC11A1CFN2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 49/158頁 |
| 文件大小： | 776K |
| 代理商： | MC68HC11A1CFN2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MC68HC11A8
TECHNICAL DATA
SERIAL COMMUNICATIONS INTERFACE
MOTOROLA
5-5
5
5.6 Transmit Data (TxD)
Transmit data is the serial data from the internal data bus which is applied through the
serial communications interface to the output line. The transmitter generates a bit time
by using a derivative of the RT clock, thus producing a transmission rate equal to 1/16
that of the receiver sample clock.
5.7 Functional Description
A block diagram of the SCI is shown in
Figure 5-6
. The user has option bits in serial
communications control register 1 (SCCR1) to determine the “wake-up” method
(WAKE bit) and data word length (M bit) of the SCI. Serial communications control reg-
ister 2 (SCCR2) provides control bits which individually enable/disable the transmitter
or receiver (TE and RE, respectively), enable system interrupts (TIE, TCIE, ILIE) and
provide the wake-up enable bit (RWU) and the send break code bit (SBK). The baud
rate register (BAUD) bits allow the user to select different baud rates which may be
used as the rate control for the transmitter and receiver.
Data transmission is initiated by a write to the serial communications data register
(SCDR). Provided the transmitter is enabled, data stored in the SCDR is transferred
to the transmit data shift register. This transfer of data sets the TDRE bit of the SCI
status register (SCSR) and may generate an interrupt if the transmit interrupt is en-
abled. The transfer of data to the transmit data shift register is synchronized with the
bit rate clock (
Figure 5-7
). All data is transmitted LSB first. Upon completion of data
transmission, the transmission complete (TC) bit of the SCSR is set (provided no
pending data, preamble, or break is to be sent), and an interrupt may be generated if
the transmit complete interrupt is enabled. If the transmitter is disabled, and the data,
preamble, or break (in the transmit shift register) has been sent, the TC bit will also be
set. This will also generate an interrupt if the TCIE bit is set. If the transmitter is dis-
abled in the middle of a transmission, that character will be completed before the trans-
mitter gives up control of the TxD pin.
When the SCDR is read, it contains the last data byte received, provided that the re-
ceiver is enabled. The RDRF bit of the SCSR is set to indicate that a data byte has
been transferred from the input serial shift register to the SCDR, which can cause an
interrupt if the receiver interrupt is enabled. The data transfer from the input serial shift
register to the SCDR is synchronized by the receiver bit rate clock. The OR (over-run),
NF (noise), or FE (framing) error bits of the SCSR may be set if data reception errors
occurred.
An idle line interrupt is generated if the idle line interrupt is enabled and the IDLE bit
(which detects idle line transmission) of SCSR is set. This allows a receiver that is not
in the wake-up mode to detect the end of a message, the preamble of a new message,
or to resynchronize with the transmitter. A valid character must be received before the
idle line condition or the IDLE bit will not be set and an idle line interrupt will not be
generated.
5.8 SCI Registers
There are five registers used in the serial communications interface and the operation
of these registers is discussed in the following paragraphs. Reference should be made
to the block diagram shown in
Figure 5-6
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HCP11A1CFN2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CFN3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MFN2 | HCMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11A1CFN3 | 制造商:Rochester Electronics LLC 功能描述: |
| MC68HC11A1CFNE3 | 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11A1CFNE3 | 制造商:Freescale Semiconductor 功能描述:8-BIT MICROCONTROLLER IC |
| MC68HC11A1CFNE3R | 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11A1CFU2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。