欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HC11A1CFN2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: HCMOS Single-Chip Microcontroller
中文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52
封裝: PLASTIC, LCC-52
文件頁數: 59/158頁
文件大小: 776K
代理商: MC68HC11A1CFN2
MC68HC11A8
TECHNICAL DATA
SERIAL PERIPHERAL INTERFACE
MOTOROLA
6-1
6
6 SERIAL PERIPHERAL INTERFACE
This section contains a description on the serial peripheral interface (SPI).
6.1 Overview and Features
The serial peripheral interface (SPI) is a synchronous interface which allows several
SPI microcontrollers or SPI-type peripherals to be interconnected. In a serial periph-
eral interface, separate wires (signals) are required for data and clock. In the SPI for-
mat, the clock is not included in the data stream and must be furnished as a separate
signal. The MC68HC11A8 SPI system may be configured either as a master or as a
slave. The SPI contains the following features:
Full Duplex, Three-Wire Synchronous Transfers
Master or Slave Operation
1.5 MHz (Maximum) Master Bit Frequency
3 MHz (Maximum) Slave Bit Frequency
Four Programmable Master Bit Rates
Programmable Clock Polarity and Phase
End-of-Transmission Interrupt Flag
Write Collision Flag Protection
Master-Master Mode Fault Protection
Easily Interfaces to Simple Expansion Parts (PLLs, D/As, Latches, Display Driv-
ers, etc.)
6.2 SPI Signal Descriptions
The four basic SPI signals (MISO, MOSI, SCK, and SS) are discussed in the following
paragraphs. Each signal is described for both the master and slave modes.
Any SPI output line has to have its corresponding data direction register bit set. If this
bit is clear, the line is disconnected from the SPI logic and becomes a general-purpose
input line. Any SPI input line is forced to act as an input regardless of what is in the
corresponding data direction register bit.
6.2.1 Master In Slave Out (MISO)
The MISO line is configured as an input in a master device and as an output in a slave
device. It is one of the two lines that transfer serial data in one direction, with the most
significant bit sent first. The MISO line of a slave device is placed in the high-imped-
ance state if the slave is not selected.
6.2.2 Master Out Slave In (MOSI)
The MOSI line is configured as an output in a master device and as an input in a slave
device. It is one of the two lines that transfer serial data in one direction with the most
significant bit sent first.
相關PDF資料
PDF描述
MC68HCP11A1CFN2 HCMOS Single-Chip Microcontroller
MC68HCP11A1CFN3 HCMOS Single-Chip Microcontroller
MC68HCP11A1CP2 HCMOS Single-Chip Microcontroller
MC68HCP11A1CP3 HCMOS Single-Chip Microcontroller
MC68HCP11A1MFN2 HCMOS Single-Chip Microcontroller
相關代理商/技術參數
參數描述
MC68HC11A1CFN3 制造商:Rochester Electronics LLC 功能描述:
MC68HC11A1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1CFNE3 制造商:Freescale Semiconductor 功能描述:8-BIT MICROCONTROLLER IC
MC68HC11A1CFNE3R 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1CFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
主站蜘蛛池模板: 饶河县| 北辰区| 酉阳| 太仓市| 潍坊市| 靖安县| 榕江县| 新龙县| 辉南县| 内黄县| 海宁市| 连江县| 乌海市| 江达县| 西昌市| 垣曲县| 中山市| 昂仁县| 平利县| 林口县| 扶沟县| 红桥区| 天长市| 水城县| 阿拉善右旗| 浪卡子县| 稷山县| 寿宁县| 什邡市| 静海县| 红原县| 简阳市| 张家界市| 元谋县| 绥德县| 桑植县| 唐海县| 甘肃省| 陕西省| 崇阳县| 进贤县|