- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCP1603D100R2G (ON Semiconductor)IC CTLR PFC/PWM COMBO 16-SOIC Datasheet資料下載
參數資料
| 型號： | NCP1603D100R2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 17/30頁 |
| 文件大小： | 302K |
| 描述： | IC CTLR PFC/PWM COMBO 16-SOIC |
| 產品變化通告： | Product Discontinuation 21/Jun/2007 |
| 標準包裝： | 2,500 |
| 模式： | 臨界傳導（CRM），間歇導電（DCM） |
| 頻率 - 開關： | 58kHz |
| 電流 - 啟動： | 17µA |
| 電源電壓： | 9 V ~ 18 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
NCP1603
http://onsemi.com
17
The recommended biasing schematic of the controller is in
Figure 47 while a typical completed application schematic
can be referred to Figure 45. These two dies have their own
individual supply voltages at Pin 8 and Pin 14. The grounds
of the two dies are physically connected through the package
substrate but they are needed to be connected externally. The
bias voltage to the NCP1603 comes from the bulk voltage
V
bulk
through the HV pin (Pin 16) during startup. After
startup, a secondstage flyback transformer auxiliary winding
delivers the supply voltage to V
CC
.
Lossless High Voltage Startup Circuit
Figure 48. V
CC2
Management
Q S
R
Double
Hiccup
B2
Counter
&
Turn Off
+
-
UVLO
3.2 mA
16
V
bulk
HV
12.6/
5.6 V
+
-
7.7 V
20 V
14
V
CC
Turn on Internal Bias
The HV pin (Pin 16) is capable of the maximum 500 V so
that this pin can be directly connected to the bulk voltage
V
bulk
and delivers startup supply voltage to the controller.
Figure 48 illustrates the block diagram of the startup circuit.
An UVLO comparator monitors the V
CC
at Pin 14. A startup
current source is activated and deactivated whenever the
voltage reaches V
CC2(latch)
(5.6 V typical) and V
CC2(on)
(12.6 V typical) thresholds respectively. Therefore, the V
CC
never drops below V
CC2(latch)
after powering up unless the
circuit is unplugged (i.e., V
bulk
disappears or smaller than its
minimum required operating threshold V
start(min)
(20 V
typical)). This feature makes the controller memorize the
external latch off function implemented in Pin 3.
This inchip startup circuit can minimize the number of
external components and Printed Circuit Board (PCB) area.
It also minimizes the loss due to startup resistor because
startup resistor always dissipates power but this startup circuit
can be turned off when the V
CC
voltage is sufficient. Actually,
there is a small leakage current I
HV3
(30 mA typical at
HV = 700 V) when the startup circuit is off.
The V
CC
capacitor is recommended to be at least 47 mF to
ensure that V
CC
is always above the minimum operating
voltage V
CC2(off)
(7.7 V typical) in the startup phase. For
example, the PWM die consumes I
CC2(op2)
(2.2 mA typical),
a 47 mF V
CC
capacitor can maintain the V
CC
above 7.7 V for
105 ms. It is the available time to establish a V
CC
voltage
from the flyback transformer auxiliary winding.
t
startup
+
C
VCC
DV
I
CC2(op2)
+
47 mF?12.6 V7.7 V)
2.2 mA
+ 105 ms
(eq. 1)
A large enough V
CC
capacitor can also help to maintain
V
CC2
always above V
CC2(off)
to prevent the IC accidentally
powered off during the standby condition where the
lowfrequency ripple of V
CC2
can be very high.
The PFC section does not consume any current in the
startup phase since V
aux
is disabled initially (i.e., V
aux
=
V
CC1
= 0 V).
When V
CC2
falls below V
CC2(off)
(7.7 V typical) for
whatever reason, the PWM section sleeps and it consumes
I
CC2(latch)
(680 mA typical) until V
CC2
reaches V
CC2(latch)
(5.6 V typical). When V
CC2
reaches V
CC2(latch)
(5.6 V
typical), the startup current source activates and V
CC2
rises
again.
Figure 49. V
aux
Enabled Regions
0.75 V
3.0 V
Non
usable
Vaux
Enabled
Region
V
FB2
Fault Condition (V
FB2
> 3.0 V)
Usable
Vaux
Enabled
Region
Standby Condition (V
FB2
< 0.75 V)
7.7 V
V
CC2
(PWM)
18 V
12.6 V
V
CC1
(PFC)
18 V
10.5 V
9.0 V
Auxiliary Supply V
aux
The V
aux
pin (Pin 1) connects to the V
CC1
pin (Pin 8)
externally. Internally, the V
aux
pin is connected to V
CC2
through an internal MOSFET. The MOSFET onresistance
is R
aux
(11.7 W typical). It delivers a supply voltage from
the PWM section to the PFC section. The V
aux
is disabled
when one of the following conditions occurs.
1. V
aux
is initially disabled because of no feedback
signal (V
FB2
> 3.0 V) initially.
2. Fault condition (V
FB2
> 3.0 V for more than
125 ms).
3. Standby condition (V
FB2
< V
stby
(0.75 V typical)
and then V
FB2
< V
stbyout
(1.25 V typical) for
more than 125 ms).
4. Insufficient operating supply voltage (V
CC2
<
V
CC2(off)
(7.7 V typical)).
5. Overvoltage protection (OVP) latch activated from
CS2 pin (Pin 3) (V
CS2
> V
OVP
(3.0 V typical)).
6. Thermal shutdown latch in the PWM section
activated when the junction temperature is over
typical 150_C.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1605DR2G | IC PFC CONTROLLER CCM/DCM 16SOIC |
| NCP1606BDR2G | IC POWER FACTOR CONTROLLER 8SOIC |
| NCP1607BDR2G | IC PFC CONTROLLER CRM 8SOIC |
| NCP1611BDR2G | IC PFC CTLR HE ENHANCED 8-SOIC |
| NCP1651DR2G | IC PFC CONTROLLER CCM/DCM 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1605ADR2G | 功能描述:功率因數校正 IC ENHANCED PFC CNTRLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1605BDR2G | 功能描述:功率因數校正 IC High Volt Stby Mode Power Fact Corr Cont RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1605DR2G | 功能描述:功率因數校正 IC Enhanced PFC HV and Eff Standby RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1605FORWGEVB | 功能描述:電源管理IC開發工具 NCP1605 152 W FORWARD EVB RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1605LCDTVGEVB | 功能描述:BOARD EVAL NCP1605/1396 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。