欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: P89LPC920
廠商: NXP Semiconductors N.V.
英文描述: 8-bit microcontrollers with two-clock 80C51 core 2 kB/4 kB/8 kB 3 V low-power Flash with 256-byte data RAM
中文描述: 8位微控制器兩個小時80C51的核心2鍵盤/ 4 KB的/ 8 KB的3伏的低功耗Flash 256 - RAM的字節數據
文件頁數: 22/45頁
文件大小: 877K
代理商: P89LPC920
Philips Semiconductors
P89LPC920/921/922
8-bit microcontrollers with two-clock 80C51 core
Product data
Rev. 06 — 21 November 2003
22 of 45
9397 750 12285
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Remark:
During a power cycle, V
DD
must fall below V
POR
(see
Table 8 “DC electrical
characteristics” on page 35
) before power is reapplied, in order to ensure a power-on
reset.
Reset can be triggered from the following sources:
External reset pin (during power-up or if user configured via UCFG1);
Power-on detect;
Brownout detect;
Watchdog Timer;
Software reset;
UART break character detect reset.
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can
read this register to determine the most recent reset source. These flag bits can be
cleared in software by writing a ‘0’ to the corresponding bit. More than one flag bit
may be set:
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
For any other reset, previously set flag bits that have not been cleared will remain
set.
8.15.1
Reset vector
Following reset, the P89LPC920/921/922 will fetch instructions from either address
0000h or the Boot address. The Boot address is formed by using the Boot Vector as
the high byte of the address and the low byte of the address = 00h.
The Boot address will be used if a UART break reset occurs, or the non-volatile Boot
Status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on
(see P89LPC920/921/922 User’s Manual). Otherwise, instructions will be fetched
from address 0000H.
8.16 Timers/counters 0 and 1
The P89LPC920/921/922 has two general purpose counter/timers which are upward
compatible with the standard 80C51 Timer 0 and Timer 1. Both can be configured to
operate either as timers or event counter. An option to automatically toggle the T0
and/or T1 pins upon timer overflow has been added.
In the ‘Timer’ function, the register is incremented every machine cycle.
In the ‘Counter’ function, the register is incremented in response to a 1-to-0 transition
at its corresponding external input pin, T0 or T1. In this function, the external input is
sampled once during every machine cycle.
Timer 0 and Timer 1 have five operating modes (modes 0, 1, 2, 3 and 6). Modes 0, 1,
2 and 6 are the same for both Timers/Counters. Mode 3 is different.
相關PDF資料
PDF描述
P89LPC931 8-bit microcontrollers with two-clock 80C51 core 4 kB/8 kB 3 V Flash with 256-byte data RAM
P8C15416Y-12 IC-8-BIT CMOS CPU
P903
P90C101ABA 16-Bit Microcontroller
P90C101ABB 16-Bit Microcontroller
相關代理商/技術參數
參數描述
P89LPC9201 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB 3 V byte-erasable flash with 8-bit ADC
P89LPC9201FDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB 3 V byte-erasable flash with 8-bit ADC
P89LPC9201FDH,112 功能描述:8位微控制器 -MCU MCU 8-Bit CISC 2KB Flash2.5V/3.3V 20Pin RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC920FDH 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 2K FLASH TSSOP20
P89LPC920FDH,529 功能描述:8位微控制器 -MCU 80C51 2K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
主站蜘蛛池模板: 丹东市| 杭锦后旗| 财经| 辰溪县| 承德市| 嵩明县| 甘泉县| 宁河县| 八宿县| 尉氏县| 洞头县| 宝鸡市| 潢川县| 阿克苏市| 南投县| 丹寨县| 土默特右旗| 金昌市| 乌兰察布市| 花垣县| 越西县| 张北县| 汾阳市| 珲春市| 潼南县| 曲松县| 游戏| 格尔木市| 芜湖县| 沛县| 阿拉善右旗| 丰城市| 博爱县| 繁昌县| 灵石县| 禄丰县| 定南县| 红桥区| 海口市| 辽阳县| 莎车县|