- 您現在的位置：買賣IC網 > PDF目錄98218 > THS1041IPWRG4 (TEXAS INSTRUMENTS INC) 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 PDF資料下載
參數資料
| 型號： | THS1041IPWRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | GREEN, PLASTIC, TSSOP-28 |
| 文件頁數： | 25/41頁 |
| 文件大小： | 810K |
| 代理商： | THS1041IPWRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
THS1041
SLAS289C OCTOBER 2001 REVISED OCTOBER 2004
31
www.ti.com
APPLICATION INFORMATION
initial clamp acquisition time (continued)
Initial acquisition can be performed in two ways:
D Pulsing the CLAMP pin as in normal operation. Provided that clamp droop (see below) is negligible, initial
acquisition is complete when the total clamped (CLAMP = high) time equals TACQ.
D Pulling the CLAMP pin high for the required acquisition time before starting normal operation. This method
is faster, though possibly less convenient for the user to implement.
clamp droop
The charging currents drawn by the sample-and-hold switched capacitor input can charge or discharge CIN,
causing the dc voltage at AIN+ to drift towards the dc bias voltage at AIN during the time between clamp pulses.
This effect is called clamp droop.
Voltage droop is a function of the AIN+ and AIN input currents to the THS1041, IIN, and the time between clamp
intervals, tD:
V
DROOP [
I
IN
C
IN
t
d
(approximate)
Worst case droop between clamping intervals occurs for maximum input bias current. Maximum input current
is IINFS, which occurs when the input level is at its maximum or minimum.
For example, at 40 MSPS IINFS is approximately 20 A for a 2-V input range at AIN (assuming 2 V appear across
RIN2—see driving the sample and hold reference inputs to calculate RIN2). Note that IINFS may vary from this
by
±30% because of processing variations and voltage dependencies. Designs should allow for this variation.
If the time td between clamping intervals is 63.5 s and CIN is 1 F, then the maximum clamp level droop between
clamp pulses is
V
DROOP
(max)
+ 20 mA 1 mF
63.5
ms + 1.25 mV (approximate, ignoring 30% tolerance)
+ 0.62 LSB at PGA gain + 1, 2 V ADC references
If this droop is greater than can be tolerated in the application, then increase CIN to slow the droop and hence
reduce the voltage change between clamp pulses.
If a high leakage capacitor is used for coupling the input source to the AIN pin then the droop may be significantly
worse than calculated above. Avoid using electrolytic and tantalum coupling capacitors as these have higher
leakage currents than nonpolarized capacitor types. Electrolytic and tantalum capacitors also tend to have
higher parasitic inductance, which can cause problems at high input frequencies.
steady-state clamp voltage error
During the clamp pulse (CLAMP = high), the dc voltage on AIN is refreshed from the clamp voltage. Provided
that droop is not excessive, clamping fully reverses the effect of droop. However, using very short clamp pulses
with long intervals between pulses (td) can result in a steady-state voltage difference, VCOS, between the dc
voltage at AIN and V(Clamp).
Figure 47 shows the approximate voltage waveform at AIN resulting from a a large clamp droop during td and
clamp voltage reacquisition during the clamp pulse time, tc.
(17)
(18)
相關PDF資料 |
PDF描述 |
|---|---|
| THS1041CDWG4 | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041IDW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041IDWG4 | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041IPWR | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041IPWG4 | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS10420RJ | 功能描述:線繞電阻器 - 底架安裝 THS10 420R 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed |
| THS10470RJ | 功能描述:線繞電阻器 - 底架安裝 THS10 470R 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed |
| THS10470RJ | 制造商:TE Connectivity 功能描述:RESISTOR WIREWOUND 470OHM 10W 5% |
| THS1047RJ | 功能描述:線繞電阻器 - 底架安裝 THS10 47R 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed |
| THS104K7J | 功能描述:線繞電阻器 - 底架安裝 THS10 4K7 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed |
發布緊急采購，3分鐘左右您將得到回復。