- 您現在的位置：買賣IC網 > PDF目錄98301 > TS86101G2BCGL (E2V TECHNOLOGIES PLC) PARALLEL, WORD INPUT LOADING, 10-BIT DAC, CBGA255 PDF資料下載
參數資料
| 型號： | TS86101G2BCGL |
| 廠商： | E2V TECHNOLOGIES PLC |
| 元件分類： | DAC |
| 英文描述： | PARALLEL, WORD INPUT LOADING, 10-BIT DAC, CBGA255 |
| 封裝： | HERMETIC SEALED, CERAMIC, BGA-255 |
| 文件頁數： | 17/57頁 |
| 文件大小： | 1030K |
| 代理商： | TS86101G2BCGL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
24
0992D–BDC–04/09
TS86101G2B
e2v semiconductors SAS 2009
6.2
Power-up Asynchronous Reset/Synchronization of Several TS86101G2B Devices
A power-on asynchronous reset is integrated on the MUXDAC. It is active during the V
EED ramp-up, (up
to 50% of its final steady-state value – V
EEA/VEED <–2.5V).
To make sure that initialization is effective, the clock should not toggle before V
EED/VEEA exceed 90% of
their final value.
This asynchronous reset allows correct initialization of the divide/4 timing circuitry that drives the 4:1
MUX, therefore providing synchronous DSP output clock signals (DSP_CK_T,DSP_CK_F) and synchro-
nous analog output signals between multiple DACs.
During the power-up reset phase, the applied (CW_IN_T,CW_IN_F) master clock should not toggle.
For initialization, three clock input configurations are authorized:
Differential clock input: the master clock can start indifferently at a logical high or low.
Single-ended clock input on CW_IN_T: the master clock must be at a logical high during reset and
start with a falling edge.
Single-ended clock input on CW_IN_F: the master clock must be at a logical low during reset and
start with a rising edge.
In all cases, the first pulse width of the master clock should last at least 100 ps and should not toggle in
an undetermined way in order to avoid metastability of the clock.
For DSP systems that require several MUXDACs to be synchronized, the following design and protocol
rules apply:
1.
The MUXDACs must be powered-up under DSP executive control, with their clocks kept inac-
tive. If used in differential mode (recommended), the clocks should be previously set to either a
high or low state, and in any case the clocks should not be toggling.
2.
A delay equalling the settling time of the power supplies (time until they reach at least 90% of
their steady state) must be respected before proceeding to step 3.
3.
The MUXDAC clocks can then be commanded to their active state. In order to reduce the prob-
ability of clock meta-stability, the first pulse should last at least 100 ps and should not toggle in
an undetermined way.
4.
All MUXDAC clock paths within a given DSP should be designed according to the standard
high-speed design rules.
相關PDF資料 |
PDF描述 |
|---|---|
| TSA0801IF | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA0801CFT | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA0801CF | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA0801IFT | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| TSA1001IF | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS86101G2BMGS | 制造商:e2v technologies 功能描述:10-BIT DAC MUXDAC 10-BIT 1.2 GSPS - Trays |
| TS86101G2BVGL | 制造商:e2v technologies 功能描述:10-BIT DAC MUXDAC 10-BIT 1.2 GSPS - Trays |
| TS861AI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RAIL TO RAIL MICROPOWER BICMOS COMPARATORS |
| TS861AID | 功能描述:校驗器 IC Single Rail-to-Rail RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| TS861AIDT | 功能描述:校驗器 IC Single Rail-to-Rail RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。