- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543H-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543H-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 109/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543H-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
v1.2
2008–2011 Teridian Semiconductor Corporation
55
Table 45: I/O RAM Registers for RTC Interrupts
Name
Location
Rst
Wk
Dir
Description
RTC_TMIN[5:0]
289E[5:0]
0
R/W The target minutes register. See below.
RTC_THR[4:0]
289F[4:0]
0
R/W
The target hours register. The RTC_T interrupt occurs
when RTC_MIN[5:0] becomes equal to RTC_TMIN[5:0]
and RTC_HR[4:0] becomes equal to RTC_THR[4:0].
2.5.5
71M6543 Temperature Sensor
The 71M6543 includes an on-chip temperature sensor for determining the temperature of its bandgap
reference. The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system for the compensation of current, voltage and energy
RTC Temperature Compensation on page 53.
Unlike earlier generation Teridian SoCs, the 71M6543 does not use the ADC to read the temperature
sensor. Instead, it uses a technique that is operational in SLP and LCD mode, as well as BRN and MSN
modes. This means that the temperature sensor can be used to compensate for the frequency variation
of the crystal, even in SLP mode while the MPU is halted. See 2.5.4.4 RTC Temperature Compensation
on page 53.
In MSN and BRN modes, the temperature sensor is awakened on command from the MPU by setting the
TEMP_START (I/O RAM 0x28B4[6]) control bit. In SLP and LCD modes, it is awakened at a regular rate
set by TEMP_PER[2:0] (I/O RAM 0x28A0[2:0]).
The result of the temperature measurement is read from the two I/O RAM locations STEMP[10:3] (I/O
RAM 0x2881) and STEMP[2:0] (I/O RAM 0x2882[7:5]). Note that both of these I/O RAM locations must be
read and properly combined to form the STEMP[10:0] 11-bit value (see STEMP in Table 46). The resulting
11-bit value is in 2’s complement form and ranges from -1024 to +1023 (decimal).
The equations below are used to calculate the sensed temperature. The first equation applies when the
71M6543F and 71M6543G are in MSN mode and TEMP_PWR = 1. The second equation applies when the
71M6543F and 71M6543G are in BRN mode, and in this case, the TEMP_PWR and TEMP_BSEL bits must
both be set to the same value, so that the battery that supplies the temperature sensor is also the battery
that is measured and reported in BSENSE. Thus, the second equation requires reading STEMP and
BSENSE. In the second equation, BSENSE (the sensed battery voltage) is used to obtain a more accurate
temperature reading when the IC is in BRN mode. A second set of equations if provided for the
71M6543H and 71M6543GH high precision parts. The coefficients provided in the various STEMP
equations below are typical.
For the 71M6543F and 71M6543G in MSN Mode (with TEMP_PWR = 1):
22
325
.
0
)
(
+
=
°
STEMP
C
Temp
For the 71M6543F and 71M6543G in BRN Mode, (with TEMP_PWR=TEMP_BSEL):
4
.
64
609
.
0
00218
.
0
325
.
0
)
(
2
+
+
=
BSENSE
STEMP
C
Temp
o
For the 71M6543H and 71M6543GH in BRN mode (with TEMP_PWR=TEMP_BSEL):
If STEMP
≤ 0:
(℃)=0.325+0.0021820.609+64.4
If STEMP > 0:
(℃)=63
_85 +0.0021820.609+64.4
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543HT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543HT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR, HIGH PRES REF - Tape and Reel |
| 71M6545 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Four-Quadrant Metering, Phase Metrology Processors Flash/RAM Size |
| 71M6545H | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Four-Quadrant Metering, Phase Metrology Processors Flash/RAM Size |
| 71M6545HT-IGT/F | 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。