欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： 71M6543H-IGTR/F
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PQFP100
封裝： LEAD FREE, LQFP-100
文件頁數： 110/157頁
文件大小： 2178K
代理商： 71M6543H-IGTR/F
71M6543F/H and 71M6543G/GH Data Sheet
56
2008–2011 Teridian Semiconductor Corporation
v1.2
Table 46 shows the I/O RAM registers used for temperature and battery measurement.
If TEMP_PWR selects VBAT_RTC when the battery is nearly discharged, the temperature
measurement may not finish. In this case, firmware may complete the measurement by selecting
V3P3D (TEMP_PWR = 1).
Table 46: I/O RAM Registers for Temperature and Battery Measurement
Name
Location
Rst
Wk
Dir
Description
TBYTE_BUSY
28A0[3]
0
R
Indicates that hardware is still writing the 0x28A0
byte. Additional writes to this byte are locked out
while it is one. Write duration could be as long as 6 ms.
TEMP_PER[2:0]
28A0[2:0]
0
–
R/W
Sets the period between temperature measurements.
Automatic measurements can be enabled in any
mode (MSN, BRN, LCD, or SLP).
TEMP_PER
Time
0
Manual updates (see TEMP_START)
1-6
2 ^ (3+TEMP_PER) (seconds)
7
Continuous
TEMP_BAT
28A0[4]
0
–
R/W
Causes VBAT to be measured whenever a
temperature measurement is performed.
TEMP_START
28B4[6]
0
–
R/W
TEMP_PER[2:0] must be zero in order for TEMP_START
to function. If TEMP_PER[2:0] = 0, then setting
TEMP_START starts a temperature measurement.
Ignored in SLP and LCD modes. Hardware clears
TEMP_START when the temperature measurement is
complete.
TEMP_PWR
28A0[6]
0
–
R/W
Selects the power source for the temperature sensor:
1 = V3P3D, 0 = VBAT_RTC. This bit is ignored in
SLP and LCD modes, where the temperature sensor is
always powered by VBAT_RTC.
TEMP_BSEL
28A0[7]
0
–
R/W
Selects which battery is monitored by the
temperature sensor: 1 = VBAT, 0 = VBAT_RTC
TEMP_TEST[1:0]
2500[1:0]
0
–
R/W
Test bits for the temperature monitor VCO.
TEMP_TEST must be 00 in regular operation. Any
other value causes the VCO to run continuously with
the control voltage described below.
TEMP_TEST
Function
00
Normal operation
01
Reserved for factory test
1X
Reserved for factory test
STEMP[10:3]
STEMP[2:0]
2881[7:0]
2882[7:5]
R
The result of the temperature measurement.
The STEMP[10:0] value may be obtained in C with a
single 16-bit read and divide by 32 operation as
follows:
volatile int16_t xdata STEMP _at_0x2881;
fa = (float)(STEMP/32);
BSENSE[7:0]
2885[7:0]
–
R
The result of the battery measurement.
BCURR
2704[3]
0
R/W
Connects a 100 A load to the battery selected by
TEMP_BSEL.
2.5.6
71M6xx3 Temperature Sensor
相關PDF資料
PDF描述
71M6543F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543GH-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543GH-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
相關代理商/技術參數
參數描述
71M6543HT-IGT/F 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543HT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR, HIGH PRES REF - Tape and Reel
71M6545 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Four-Quadrant Metering, Phase Metrology Processors Flash/RAM Size
71M6545H 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Four-Quadrant Metering, Phase Metrology Processors Flash/RAM Size
71M6545HT-IGT/F 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 海阳市| 礼泉县| 柳林县| 噶尔县| 淳安县| 南昌县| 米脂县| 聂拉木县| 佛教| 红原县| 宁津县| 满城县| 平昌县| 喀喇沁旗| 宁蒗| 嫩江县| 石棉县| 错那县| 翁牛特旗| 普安县| 清水河县| 洪湖市| 中山市| 龙陵县| 托里县| 怀柔区| 黄大仙区| 武安市| 盱眙县| 哈尔滨市| 青川县| 恩平市| 垫江县| 衡阳市| 青田县| 建水县| 潼南县| 花莲县| 兴业县| 文安县| 龙山县|