- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543H-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543H-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 33/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543H-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
128
2008–2011 Teridian Semiconductor Corporation
v1.2
the source for pulse generation in APULSEW and APULSER to generate pulses. Irrespective of the
EXT_PULSE status, the output pulse rate controlled by APULSEW and APULSER is implemented by the CE
only. By setting EXT_PULSE = 1, the MPU is providing the source for pulse generation. If EXT_PULSE is 0,
W0SUM_X and VAR0SUM_X are the default pulse generation sources. In this case, creep cannot be
controlled since it is an MPU function.
The maximum pulse rate is 3*FS = 7.5 kHz.
See 2.3.6.2 VPULSE and WPULSE (page 27) for details on how to adjust the timing of the output pulses.
The maximum time jitter is 1/6 of the multiplexer cycle period (nominally 67 s) and is independent of the
number of pulses measured. Thus, if the pulse generator is monitored for one second, the peak jitter is
67 ppm. After 10 seconds, the peak jitter is 6.7 ppm. The average jitter is always zero. If it is attempted
to drive either pulse generator faster than its maximum rate, it simply outputs at its maximum rate without
exhibiting any rollover characteristics. The actual pulse rate, using WSUM as an example, is:
Hz
X
F
WSUM
WRATE
RATE
S
46
2
=
,
where FS = sampling frequency (2184.53 Hz), X = Pulse speed factor derived from the CE variables
PULSE_SLOW (CE RAM 0x20[0]) and PULSE_FAST (CE RAM 0x20[1]).
Table 85: CE Pulse Generation Parameters
CE
Address
Name
Default
Description
0x21
WRATE
227
Kh = VMAX*IMAX*K / (WRATE*NACC*X) Wh/pulse
where:
K = 76.3594 when used with local sensors (CT or shunt)
K = 54.5793 when used with 71M6xx3 remote sensors
0x22
KVAR
6444
Scale factor for VAR measurement.
0x23
SUM_PRE
2184
Number of samples per accumulation interval, as specified in
SUM_SAMPS[12:0], I/O RAM 0x2107[4:0], 0x2108[7:0] (NACC).
0x45
APULSEW
0
Wh pulse (WPULSE) generator input to be updated by the MPU
when using external pulse generation. The output pulse rate is:
APULSEW * FS * 2
-32 * WRATE * X * 2-14.
This input is buffered and can be updated by the MPU during a
conversion interval. The change takes effect at the beginning of
the next interval.
0x46
WPULSE_CTR
0
Counter for WPULSE output.
0x47
WPULSE_ FRAC
0
Unsigned numerator, containing a fraction of a pulse. The value
in this register always counts up towards the next pulse.
0x48
WSUM_ ACCUM
0
Roll-over accumulator for WPULSE.
0x49
APULSER
0
VARh (VPULSE) pulse generator input.
0x4A
VPULSE_CTR
0
Counter for VPULSE output.
0x4B
VPULSE_ FRAC
0
Unsigned numerator, containing a fraction of a pulse. The value
in this register always counts up towards the next pulse.
0x4C
VSUM_ACCUM
0
Roll-over accumulator for VPULSE.
Other CE Parameters
Table 86 shows the QUANT CE parameters used for suppression of noise due to scaling and truncation
effects. The equations for calculating the LSB weight of each QUANT parameter are provided at the
bottom of Table 86.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543HT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543HT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR, HIGH PRES REF - Tape and Reel |
| 71M6545 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Four-Quadrant Metering, Phase Metrology Processors Flash/RAM Size |
| 71M6545H | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Four-Quadrant Metering, Phase Metrology Processors Flash/RAM Size |
| 71M6545HT-IGT/F | 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。