- 您現在的位置：買賣IC網 > PDF目錄373969 > AD9859 (Analog Devices, Inc.) 400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer PDF資料下載
參數資料
| 型號： | AD9859 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | XO, clock |
| 英文描述： | 400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| 中文描述： | 400 MSPS的10位，1.8伏的CMOS直接數字頻率合成 |
| 文件頁數： | 21/24頁 |
| 文件大小： | 574K |
| 代理商： | AD9859 |
AD9859
INSTRUCTION BYTE
The instruction byte contains the following information:
Table 7.
MSB
D6
R/W
X
Rev. 0 | Page 21 of 24
D5
X
D4
A4
D3
A3
D2
A2
D1
A1
LSB
A0
R/W—Bit 7 of the instruction byte determines whether a read
or write data transfer occurs after the instruction byte write.
Logic High indicates read operation. Logic 0 indicates a write
operation.
X, X—Bits 6 and 5 of the instruction byte are Don’t Cares.
A4, A3, A2, A1, A0—Bits 4, 3, 2, 1, 0 of the instruction byte
determine which register is accessed during the data transfer
portion of the communications cycle.
SERIAL INTERFACE PORT PIN DESCRIPTION
SCLK—Serial Clock. The serial clock pin is used to synchronize
data to and from the AD9859 and to run the internal state
machines. SCLK maximum frequency is 25 MHz.
CSB—Chip Select Bar. CSB is active low input that allows more
than one device on the same serial communications line. The
SDO and SDIO pins go to a high impedance state when this
input is high. If driven high during any communications cycle,
that cycle is suspended until CS is reactivated low. Chip select
can be tied low in systems that maintain control of SCLK.
SDIO—Serial Data I/O. Data is always written to the AD9859
on this pin. However, this pin can be used as a bidirectional data
line. Bit 7 of Register Address 0x00 controls the configuration of
this pin. The default is Logic 0, which configures the SDIO pin
as bidirectional.
SDO—Serial Data Out. Data is read from this pin for protocols
that use separate lines for transmitting and receiving data. In the
case where the AD9859 operates in a single bidirectional I/O
mode, this pin does not output data and is set to a high imped-
ance state.
IOSYNC—It synchronizes the I/O port state machines without
affecting the addressable register’s contents. An active high
input on the IOSYNC pin causes the current communication
cycle to abort. After IOSYNC returns low (Logic 0), another
communication cycle may begin, starting with the instruction
byte write.
MSB/LSB TRANSFERS
The AD9859 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by the Control Register 0x00 <8> bit.
The default value of Control Register 0x00 <8> is low (MSB
first). When Control Register 0x00 <8> is set high, the AD9859
serial port is in LSB first format. The instruction byte must be
written in the format indicated by Control Register 0x00 <8>. If
the AD9859 is in LSB first mode, the instruction byte must be
written from least significant bit to most significant bit.
For MSB first operation, the serial port controller generates the
most significant byte (of the specified register) address first
followed by the next lesser significant byte addresses until the
I/O operation is complete. All data written to (read from) the
AD9859 must be (is) in MSB first order. If the LSB mode is ac-
tive, the serial port controller generates the least significant byte
address first followed by the next greater significant byte ad-
dresses until the I/O operation is complete. All data written to
(read from) the AD9859 must be (is) in LSB first order.
Example Operation
To write the amplitude scale factor register in MSB first format,
apply an instruction byte of 0x02 [serial address is 00010(b)].
From this instruction, the internal controller knows to use the
first byte as the most significant byte. The first two bits are
recorded as the auto ramp rate speed control bits, and the next
six bits are the most significant bits of the amplitude scale fac-
tor. The second byte is applied as the eight less significant bits of
the amplitude scale factor ASF<7:0>.
To write the amplitude scale factor register in LSB first format,
assuming the control register has already been set for LSB first
format, apply an instruction byte of 0x40. From this instruction,
the internal controller knows to use the first byte as the least
significant byte of the amplitude scale factor ASF<0:7>. The
second byte is split into the first six bits ASF<8:13> and the last
two provide the auto-ramp rate speed control bits ARRSC<0:1>.
Power-Down Functions of the AD9859
The AD9859 supports an externally controlled or hardware
power-down feature as well as the more common software pro-
grammable power-down bits found in previous ADI DDS products.
The software control power-down allows the DAC, PLL, input
clock circuitry, and digital logic to be individually powered
down via unique control bits (CFR1<7:4>). With the exception
of CFR1<6>, these bits are not active when the externally con-
trolled power-down pin (PWRDWNCTL) is high. External
power-down control is supported on the AD9859 via the
PWRDWNCTL input pin. When the PWRDWNCTL input pin
is high, the AD9859 enters a power-down mode based on the
CFR1<3> bit. When the PWRDWNCTL input pin is low, the
external power-down control is inactive.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9859YSV | 400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| AD9859YSV-REEL7 | 400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| AD9862PCB | Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications |
| AD9860 | Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications |
| AD9860BST | Mixed-Signal Front-End (MxFE⑩) Processor for Broadband Communications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9859/PCB | 制造商:Analog Devices 功能描述:NCO, 400MSPS 10 BIT, 1.8V CMOS DIRECT DGTL SYNTHESIZER - Bulk |
| AD9859/PCBZ | 功能描述:BOARD EVAL FOR AD9859 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:AgileRF™ 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| AD9859/PCBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 10-Bit,1.8 V CMOS Direct Digital Synthesizer |
| AD9859_09 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| AD9859YSV | 制造商:Analog Devices 功能描述:Direct Digital Synthesizer 400MHz 1-DAC 10-Bit Serial 48-Pin TQFP EP 制造商:Analog Devices 功能描述:DDS 10BIT DAC 400MSPS SMD 9859 |
發布緊急采購，3分鐘左右您將得到回復。