- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9883 (Analog Devices, Inc.) 110 MSPS Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9883 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 110 MSPS Analog Interface for Flat Panel Displays |
| 中文描述： | 110 MSPS的模擬接口的平板顯示器 |
| 文件頁數： | 20/24頁 |
| 文件大?。?/td> | 177K |
| 代理商： | AD9883 |
REV. 0
AD9883
–20–
2-WIRE SERIAL CONTROL PORT
A 2-wire serial interface control interface is provided. Up to four
AD9883 devices may be connected to the 2-wire serial interface,
with each device having a unique address.
The 2-wire serial interface comprises a clock (SCL) and a bidi-
rectional data (SDA) pin. The Analog Flat Panel Interface acts
as a slave for receiving and transmitting data over the serial inter-
face. When the serial interface is not active, the logic levels on
SCL and SDA are pulled HIGH by external pull-up resistors.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is LOW. If SDA changes state while SCL
is HIGH, the serial interface interprets that action as a start or
stop sequence.
There are six components to serial bus operation:
Start Signal
Slave Address Byte
Base Register Address Byte
Data Byte to Read or Write
Stop Signal
When the serial interface is inactive (SCL and SDA are HIGH)
communications are initiated by sending a start signal. The start
signal is a HIGH-to-LOW transition on SDA while SCL is
HIGH. This signal alerts all slaved devices that a data transfer
sequence is coming.
The first eight bits of data transferred after a start signal com-
prising a 7-bit slave address (the first seven bits) and a single R/
W
bit (the eighth bit). The R/
W
bit indicates the direction of data
transfer, read from (1) or write to (0) the slave device. If the
transmitted slave address matches the address of the device (set by
the state of the SA
1-0
input pins in Table XXXIV, the AD9883
acknowledges by bringing SDA LOW on the 9th SCL pulse. If
the addresses do not match, the AD9883 does not acknowledge.
Table XXXIV. Serial Port Addresses
Bit 7
A
6
(MSB)
Bit 6
A
5
Bit 5
A
4
Bit 4
A
3
Bit 3
A
2
Bit 2
A
1
Bit 1
A
0
1
1
0
0
0
0
1
1
1
1
0
0
0
1
Data Transfer via Serial Interface
For each byte of data read or written, the MSB is the first bit of
the sequence.
If the AD9883 does not acknowledge the master device during a
write sequence, the SDA remains HIGH so the master can
generate a stop signal. If the master device does not acknowledge
the AD9883 during a read sequence, the AD9883 interprets this
as “end of data.” The SDA remains HIGH so the master can
generate a stop signal.
Writing data to specific control registers of the AD9883 requires
that the 8-bit address of the control register of interest be written
after the slave address has been established. This control register
address is the base address for subsequent write operations. The
base address autoincrements by one for each byte of data written
after the data byte intended for the base address. If more bytes
are transferred than there are available addresses, the address will
not increment and remain at its maximum value of 14h. Any base
address higher than 14h will not produce an acknowledge signal.
Data is read from the control registers of the AD9883 in a similar
manner. Reading requires two data transfer operations:
The base address must be written with the R/
W
bit of the slave
address byte LOW to set up a sequential read operation.
Reading (the R/
W
bit of the slave address byte HIGH) begins at
the previously established base address. The address of the read
register autoincrements after each byte is transferred.
To terminate a read/write sequence to the AD9883, a stop sig-
nal must be sent. A stop signal comprises a LOW-to-HIGH
transition of SDA while SCL is HIGH.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first generat-
ing a stop signal to terminate the current communication. This
is used to change the mode of communication (read, write)
between the slave and master without releasing the serial inter-
face lines.
SDA
SCL
t
BUFF
t
STAH
t
DHO
t
DSU
t
DAL
t
DAH
t
STASU
t
STOSU
Figure 9. Serial Port Read/Write Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9886 | Analog Interface for Flat Panel Displays |
| AD9886KS-100 | Analog Interface for Flat Panel Displays |
| AD9886KS-140 | Analog Interface for Flat Panel Displays |
| AD9898 | CCD Signal Processor with Precision Timing⑩ Generator |
| AD9898KCP-20 | CCD Signal Processor with Precision Timing⑩ Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9883/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS Analog Interface for Flat Panel Displays |
| AD9883A | 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883A/PCB | 制造商:Analog Devices 功能描述:110MHZ ANALOG INTERFACE FOR SG |
| AD9883ABST-100 | 制造商:Analog Devices 功能描述:110MHZ ANALOG INTERFACE FOR SGA FPD - Bulk |
| AD9883ABST-110 | 制造商:Analog Devices 功能描述:ADC Triple 110Msps 8-bit Parallel 80-Pin LQFP |
發布緊急采購，3分鐘左右您將得到回復。