- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9883A (Analog Devices, Inc.) 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9883A |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| 中文描述： | 110 MSPS/140 MSPS的模擬接口的平板顯示器 |
| 文件頁數： | 23/28頁 |
| 文件大?。?/td> | 229K |
| 代理商： | AD9883A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁
REV. B
AD9883A
–23–
Data is read from the control registers of the AD9883A in a similar
manner. Reading requires two data transfer operations:
The base address must be written with the R/
W
Bit of the slave
address byte low to set up a sequential read operation.
Reading (the R/
W
Bit of the slave address byte high) begins at
the previously established base address. The address of the read
register autoincrements after each byte is transferred.
To terminate a read/write sequence to the AD9883A, a stop
signal must be sent. A stop signal comprises a low-to-high tran-
sition of SDA while SCL is high.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first generating
a stop signal to terminate the current communication. This is
used to change the mode of communication (read, write)
between the slave and master without releasing the serial
interface lines.
Serial Interface Read/Write Examples
Write to one control register
Start Signal
Slave Address Byte (R/
W
Bit = Low)
Base Address Byte
Data Byte to Base Address
Stop Signal
Write to four consecutive control registers
Start Signal
Slave Address Byte (R/
W
Bit = Low)
Base Address Byte
Data Byte to Base Address
Data Byte to (Base Address + 1)
Data Byte to (Base Address + 2)
Data Byte to (Base Address + 3)
Stop Signal
Read from one control register
Start Signal
Slave Address Byte (R/
W
Bit = Low)
Base Address Byte
Start Signal
Slave Address Byte (R/
W
Bit = High)
Data Byte from Base Address
Stop Signal
Read from four consecutive control registers
Start Signal
Slave Address Byte (R/
W
Bit = Low)
Base Address Byte
Start Signal
Slave Address Byte (R/
W
Bit = High)
Data Byte from Base Address
Data Byte from (Base Address + 1)
Data Byte from (Base Address + 2)
Data Byte from (Base Address + 3)
Stop Signal
BIT 7
ACK
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SDA
SCL
Figure 11. Serial Interface—Typical Byte Transfer
SYNC STRIPPER
ACTIVITY
DETECT
NEGATIVE PEAK
CLAMP
COMP
SYNC
SOG
HSYNC IN
ACTIVITY
DETECT
MUX 2
HSYNC OUT
PIXEL CLOCK
MUX 1
SYNC SEPARATOR
INTEGRATOR
VSYNC
SOG OUT
HSYNC OUT
VSYNC OUT
MUX 4
VSYNC IN
1/S
PLL
HSYNC
ACTIVITY
DETECT
AD9883A
CLOCK
GENERATOR
POLARITY
DETECT
POLARITY
DETECT
POLARITY
DETECT
MUX 3
COAST
COAST
Figure 12. Sync Processing Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD9883ABST-RL110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883ABST-110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883ABST-140 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883AKSTZ-110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9883AKSTZ-140 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9883A/PCB | 制造商:Analog Devices 功能描述:110MHZ ANALOG INTERFACE FOR SG |
| AD9883ABST-100 | 制造商:Analog Devices 功能描述:110MHZ ANALOG INTERFACE FOR SGA FPD - Bulk |
| AD9883ABST-110 | 制造商:Analog Devices 功能描述:ADC Triple 110Msps 8-bit Parallel 80-Pin LQFP |
| AD9883ABST-140 | 制造商:Analog Devices 功能描述:ADC Triple 140Msps 8-bit Parallel 80-Pin LQFP |
| AD9883ABST-RL110 | 制造商:Analog Devices 功能描述:ADC Triple 110Msps 8-bit Parallel 80-Pin LQFP T/R |
發布緊急采購，3分鐘左右您將得到回復。