欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADP3166JRU-REEL
廠商: ANALOG DEVICES INC
元件分類: 穩壓器
英文描述: 5-Bit Programmable 2-, 3-, 4-Phase Synchronous Buck Controller
中文描述: SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28
封裝: TSSOP-28
文件頁數: 19/20頁
文件大?。?/td> 351K
代理商: ADP3166JRU-REEL
REV. 0
ADP3166
–19–
Power Circuitry
The switching power path should be routed on the PCB to
encompass the shortest possible length to minimize radiated
switching noise energy (i.e., EMI) and conduction losses in
the board. Failure to take proper precautions often results in
EMI problems for the entire PC system as well as noise-
related operational problems in the power converter control
circuitry. The switching power path is the loop formed by
the current path through the input capacitors and the power
MOSFETs including all interconnecting PCB traces and
planes. The use of short and wide interconnection traces is
especially critical in this path for two reasons: it minimizes
the inductance in the switching loop, which can cause high
energy ringing, and it accommodates the high current
demand with minimal voltage loss.
Whenever a power dissipating component (e.g., a power
MOSFET) is soldered to a PCB, the liberal use of vias, both
directly on the mounting pad and immediately surrounding
it, is recommended. Two important reasons for this are
improved current rating through the vias, and improved
thermal performance from vias extended to the opposite side
of the PCB where a plane can more readily transfer the heat
to the air. Make a mirror image of any pad being used to
heatsink the MOSFETs on the opposite side of the PCB to
achieve the best thermal dissipation to the air around the
board. To further improve thermal performance, the largest
possible pad area should be used.
The output power path should also be routed to encompass
a short distance. The output power path is formed by the
current path through the inductor, the output capacitors,
and the load.
For best EMI containment, a solid power ground plane
should be used as one of the inner layers extending fully
under all the power components.
Signal Circuitry
The output voltage is sensed and regulated between the
FB pin and the FBRTN pin, which connects to the signal
ground at the load. To avoid differential mode noise pickup
in the sensed signal, the loop area should be small. Therefore
the FB and FBRTN traces should be routed adjacent to each
other on top of the power ground plane back to the controller.
The feedback traces from the switch nodes should be con-
nected as close as possible to the inductor. The CSREF
signal should be connected to the output voltage at the
inductor nearest to the controller.
相關PDF資料
PDF描述
ADP3166JRU-REEL7 5-Bit Programmable 2-, 3-, 4-Phase Synchronous Buck Controller
ADP3170JRU VRM 8.5 Compatible Single Phase Core Controller
ADP3170 Charger front end protection IC with 30V max Vin and 4.5V LDO output 8-WSON 0 to 125
ADP3171JR Charger front end protection IC with 30V max Vin and 4.5V LDO output 8-WSON 0 to 125
ADP3171 Charger front end protection IC with 30V max Vin and 4.5V LDO output 8-WSON 0 to 125
相關代理商/技術參數
參數描述
ADP3166JRU-REEL7 功能描述:IC REG BUCK 5BIT 2-4PHAS 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源,ICERA E400,E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA,WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ADP3166JRUZ-REEL 功能描述:IC REG BUCK 5BIT 2-4PHAS 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源,ICERA E400,E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA,WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ADP3167 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADP3160/ADP3167: 5-Bit Programmable 2-Phase Synchronous Buck Controller Data Sheet (Rev. B. 5/02)
ADP3167JR 制造商:Rochester Electronics LLC 功能描述:- Bulk
ADP3167JR-REEL7 制造商:Rochester Electronics LLC 功能描述:5BIT PROG'BLE 2 PHASE SYNCRO BUCK CNTRLR - Tape and Reel
主站蜘蛛池模板: 海阳市| 衡东县| 木兰县| 祁连县| 东至县| 和平县| 临沧市| 华容县| 岑溪市| 松原市| 临潭县| 盐山县| 刚察县| 吉林市| 广灵县| 开远市| 达拉特旗| 墨脱县| 秦安县| 山东省| 祁阳县| 郁南县| 湘乡市| 大埔区| 赣榆县| 庆云县| 秭归县| 天峨县| 临沭县| 醴陵市| 大丰市| 鸡东县| 诏安县| 翁牛特旗| 集贤县| 丹寨县| 湘潭县| 酉阳| 冷水江市| 浦江县| 来宾市|