- 您現在的位置：買賣IC網 > PDF目錄374036 > ADSP-2186L (Analog Devices, Inc.) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | ADSP-2186L |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 7/34頁 |
| 文件大小： | 256K |
| 代理商： | ADSP-2186L |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
ADSP-2186L
–7–
REV. A
Clock Signals
The ADSP-2186L can be clocked by either a crystal or a
TTL-compatible clock signal.
The CLKIN input cannot be halted, changed during operation
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information on the power-down
feature, refer to the
ADSP-2100 Family User’s Manual
, Third
Edition.
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is con-
nected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
The ADSP-2186L uses an input clock with a frequency equal to
half the instruction rate; a 0.20 MHz input clock yields a 25 ns
processor cycle (which is equivalent to 40 MHz). Normally,
instructions are executed in a single processor cycle. All device
timing is relative to the internal instruction clock rate, which is
indicated by the CLKOUT signal when enabled.
Because the ADSP-2186L includes an on-chip oscillator circuit,
an external crystal may be used. The crystal should be connected
across the CLKIN and XTAL pins, with two capacitors con-
nected as shown in Figure 3. Capacitor values are dependent on
crystal type and should be specified by the crystal manufacturer.
A parallel-resonant, fundamental frequency, microprocessor-
grade crystal should be used.
A clock output (CLKOUT) signal is generated by the proces-
sor at the processor’s cycle rate. This can be enabled and
disabled by the CLKODIS bit in the SPORT0 Autobuffer
Control Register.
CLKIN
CLKOUT
XTAL
DSP
Figure 3. External Crystal Connections
Reset
The
RESET
signal initiates a master reset of the ADSP-2186L.
The
RESET
signal must be asserted during the power-up
sequence to assure proper initialization.
RESET
during initial
power-up must be held long enough to allow the internal clock
to stabilize. If
RESET
is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid V
DD
is
applied to the processor, and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum of
2000 CLKIN cycles ensures that the PLL has locked, but does
not include the crystal oscillator start-up time. During this
power-up sequence the
RESET
signal should be held low. On
any subsequent resets, the
RESET
signal must meet the mini-
mum pulsewidth specification, t
RSP
.
The
RESET
input contains some hysteresis; however, if an RC
circuit is used to generate the
RESET
signal, an external Schmidt
trigger is recommended.
The master
RESET
sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When
RESET
is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes. In an EZ-ICE-compatible system
RESET
and
ERESET
have the same functionality. For complete information,
see Designing an EZ-ICE-Compatible System section.
MEMORY ARCHITECTURE
The ADSP-2186L provides a variety of memory and peripheral
interface options. The key functional groups are Program Memory,
Data Memory, Byte Memory and I/O.
Program Memory
(Full Memory Mode)
is a 24-bit-wide space
for storing both instruction opcodes and data. The ADSP-2186L
has 8K words of Program Memory RAM on chip, and the capabil-
ity of accessing up to two 8K external memory overlay spaces using
the external data bus. Both an instruction opcode and a data value
can be read from on-chip program memory in a single cycle.
Data Memory (Full Memory Mode)
is a 16-bit-wide space
used for the storage of data variables and for memory-mapped
control registers. The ADSP-2186L has 8K words on Data
Memory RAM on chip, consisting of 8160 user-accessible
locations and 32 memory-mapped registers. Support also exists
for up to two 8K external memory overlay spaces through the
external data bus.
Byte Memory
(Full Memory Mode)
provides access to an
8-bit wide memory space through the Byte DMA (BDMA) port.
The Byte Memory interface provides access to 4 MBytes of
memory by utilizing eight data lines as additional address lines.
This gives the BDMA Port an effective 22-bit address range. On
power-up, the DSP can automatically load bootstrap code from
byte memory.
I/O Space
(Full Memory Mode)
allows access to 2048 loca-
tions of 16-bit-wide data. It is intended to be used to communi-
cate with parallel peripheral devices such as data converters and
external registers or latches.
Program Memory
The ADSP-2186L contains an 8K
×
24 on-chip program RAM.
The on-chip program memory is designed to allow up to two
accesses each cycle so that all operations can complete in a
single cycle. In addition, the ADSP-2186L allows the use of 8K
external memory overlays.
The program memory space organization is controlled by the
Mode B pin and the PMOVLAY register. Normally, the ADSP-
2186L is configured with Mode B = 0 and program memory
organized as shown in Figure 4.
EXTERNAL 8K
(PMOVLAY = 1 or 2,
MODE B = 0)
0x3FFF
0x2000
0x1FFF
8K INTERNAL
0x0000
PROGRAM MEMORY
ADDRESS
Figure 4. Program Memory (Mode B = 0)
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2186MBST-266 | DSP Microcomputer |
| ADSP-2186M | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADSP-2186MKST-300 | DSP Microcomputer |
| ADSP-2186MKCA-300 | CAP 33PF 50V 1206 |
| ADSP-2186MBCA-266 | DSP Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2186L1111 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2186LBCA-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:8K/8K 16 BIT DSP 40 MIPS 3.3V MINI BGA - Bulk |
| ADSP2186LBCA-160 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP-2186LBCA-160R | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 144-Pin CSP-BGA T/R |
| ADSP-2186LBCA-160R3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。